Boeing NB-52A 52-003 with a North American Aviation X-15 under its right wing, at Edwards Air Force Base, 31 December 1961. (NASA)
29 November 1957: The third production Boeing B-52A-1-BO Stratofortress strategic bomber, 52-003, was flown from Boeing’s Seattle plant to the North American Aviation facility at Air Force Plant 42, Palmdale, California, to be modified to carry the new X-15 hypersonic research rocketplane.
Modifications began on 4 February 1958. A pylon was mounted under the bomber’s right wing. A large notch was cut into the trailing edge of the inboard flap for the X-15’s vertical fin. A 1,500 gallon (5,678 liter) liquid oxygen tank was installed in the bomb bay.
The X-15 was attached to this underwing pylon by three remotely-actuated standard Air Force bomb shackles. (NASA)To allow clearance for the X-15’s vertical fin, a notch had to be cut in the trailing edge of the inboard right flap. (NASA)
A station for a launch operator was installed on the upper deck of the B-52 at the former electronic countermeasures position. A series of control panels allowed the panel operator to monitor the X-15’s systems, provide electrical power, and to keep the rocketplane’s liquid oxygen tank full as the LOX boiled off during the climb to launch altitude. The operator could see the X-15 through a plexiglas dome, and there were two television monitors.
NB-52 liquid oxygen panel. (NASA)
After modifications were completed at Palmdale, 52-003 was flown to Edwards Air Force Base, 14 November 1958.
NB-52A 52-003 is on display at the Pima Air and Space Museum, Tucson, Arizona.
A North American Aviation F-100F Super Sabre chase plane checks an X-15 as its APUs are activated just prior to being released from NB-52A 52-003. (NASA)
At the left, Boeing NB-52A 52-003 carries X-15 56-6670 while on the right, NB-52B 52-008 carries X-15 56-6671. (NASA)
4 November 1960: This photo shows one of the four attempts NASA made at launching two X-15 aircraft in one day. This attempt occurred November 4, 1960.
None of the four attempts was successful, although one of the two aircraft involved in each attempt usually made a research flight.
In this case, Air Force test pilot Major Robert A. Rushworth flew X-15 #1, 56-6670, on its sixteenth flight to a speed of Mach 1.95 and an altitude of 48,900 feet (14,905 meters).
North American Aviation X-15A-2 56-6671 on Rogers Dry Lake. In addition to the lengthened fuselage and external tanks, the nose wheel strut is longer and the windshields have been changed to an oval shape. A wheeled dolly supports the aft end of the rocketplane. (NASA)
3 November 1965: Major Robert A. Rushworth made the first flight of the modified X-15A-2 rocketplane, Air Force serial number 56-6671. After a landing accident which caused significant damage to the Number 2 X-15, it was rebuilt by North American Aviation. A 28-inch (0.71 meter) “plug” was installed in the fuselage forward of the wings to create space for a liquid hydrogen fuel tank which would be used for an experimental “scramjet” engine that would be mounted on the the ventral fin. The modified aircraft was also able to carry two external fuel tanks. It was hoped that additional propellant would allow the X-15A-2 to reach much higher speeds.
The first flight with the new configuration was an “envelope expansion” flight, intended to test the handling characteristics of the X-15A-2, and to jettison the tanks (which were empty on this flight) to evaluate the separation and trajectory as they fell away from the rocketplane in supersonic flight.
Boeing NB-52A Stratofortress 52-003, The High and Mighty One, with North American Aviation X-15A-2 56-6671 mounted to the pylon under its right wing. The external propellant tanks have been brightly painted to aid tracking after they are jettisoned. (U.S. Air Force)
The X-15A-2 was dropped from the Boeing NB-52A Stratofortress 52-003, over Cuddeback Lake, 37 miles (60 kilometers) northeast of Edwards Air Force Base in the Mojave Desert of southern California. This was the only time during the 199-flight X-15 Program that this lake was used as a launch point.
The X-15 was released at 09:09:10.7 a.m., PST. Bob Rushworth ignited the Reaction Motors XLR99-RM-1 rocket engine and it ran for 84.1 seconds before its fuel supply was exhausted. This engine was rated at 57,000 pounds of thrust (253.549 kilonewtons).
The X-15 climbed to 70,600 feet (21,519 meters) and reached Mach 2.31 (1,514 miles per hour/2,437 kilometers per hour.)
The test flight went well. The external tanks jettisoned cleanly and fell away. The recovery parachute for the liquid oxygen tank did not deploy, however, and the tank was damaged beyond repair.
Rushworth and the X-15A-2 touched down on Rogers Dry Lake after a flight of 5 minutes, 1.6 seconds.
William Harvey Dana, NASA Research Pilot. (National Aeronautics and Space Administration E-5327)
24 October 1968: William Harvey Dana takes the first North America Aviation X-15 hypersonic research rocketplane, 56-6670, for the 199th and final flight of the X-15 program.
Carried aloft by NASA’s Boeing NB-52A Stratofortress mothership, 52-003, the first X-15A was launched over Smith Ranch Dry Lake, about half-way between the city of Reno and the NASA High Range Tracking Station at Ely, Nevada, at 10:02:47.3 a.m., Pacific Daylight Time (17:02:47.3 UTC). Bill Dana started the Reaction Motors XLR99-RM-1 rocket engine for a planned 84 second burn. The flight plan called for the X-15 to reach Mach 5.45 and 250,000 feet (76,200 meters).
The rocketplane’s performance was very close to plan, a tribute to Dana’s piloting skill. The engine burned out after 83.8 seconds. The maximum speed was slightly lower than planned at Mach 5.38, while the peak altitude was a little higher, at 255,000 feet (77,724 meters).
Dana glided back to Edwards Air Force Base. The total duration of the flight was 11 minutes, 28.3 seconds.
Dana made his first flight in the North American Aviation X-15 hypersonic research rocketplane on 4 November 1965. He reached a maximum speed of Mach 4.22, and a peak altitude of 80,200 feet (24,445 meters). He made a total of sixteen flights in the X-15s. Dana’s highest speed was Mach 5.38, and his highest altitude, 306,900 feet, (93,543 meters), on 1 November 1966.
This had been 56-6670’s 81st flight, and the 141st time it had been carried aloft aboard a B-52.
A. Scott Crossfield, wearing a David Clark Co. XMC-2 full-pressure suit, which he helped to design and test, with the first of three North American X-15s, 56-6670. (North American Aviation, Inc.)
56-6670 is the first of three X-15s built by North American Aviation’s Los Angeles Division for NASA, the United States Air Force, and the United States Navy, to investigate the effects of hypersonic flight (Mach 5+). On 8 June 1959, North American Aviation Chief Engineering Test Pilot, and former NACA research test pilot, Albert Scott Crossfield, had made the first glide flight of 56-6670, also launched by 52-003.
NASA Research Pilot William H. Dana with North American X-15A 56-6672 on Rogers Dry Lake. (NASA)
From 8 June 1959 to 24 October 1968, the three X-15s were flown by twelve test pilots, three of whom would qualify as astronauts in the X-15. Two would go on to the Apollo Program, and one, Neil Alden Armstrong, would be the first human to set foot on the surface of the Moon, 20 July 1969. Joe Engle would fly the space shuttle. Four of the test pilots, Petersen, White, Rushworth, and Knight, flew in combat during the Vietnam War, with Bob White being awarded the Air Force Cross. Petersen, Rushworth and White reached flag rank.
Overhead view of X-15A-1 56-6670 shows the rocketplane’s overall fineness ratio and short wings. (North American Aviation, Inc.)
Flown by a single pilot/astronaut, the X-15 is a mid-wing monoplane with dorsal and ventral fin/rudders and stabilators. The wing had no dihedral, while the stabilators had a pronounced 15° anhedral. The short wings have an area of 200 square feet (18.58 square meters) and a maximum thickness of just 5%. The leading edges are swept to 25.64°. There are two small flaps but no ailerons. The entire vertical fin pivots for yaw control.
Above 100,000 feet (30,840 meters) altitude, conventional aircraft flight control surfaces are ineffective. The X-15 is equipped with a system of reaction control jets for pitch, roll and yaw control. Hydrogen peroxide was passed through a catalyst to produce steam, which supplied the control thrusters.
The forward landing gear consists of a retractable oleo strut with steerable dual wheels and there are two strut/skids at the rear of the fuselage. The gear is retracted after the X-15 is mounted on the NB-52 and is extended for landing by its own weight.
The rocketplane’s cockpit featured both a conventional control stick as well as side-controllers. It was pressurized with nitrogen gas to prevent fires. The pilot wore an MC-2 full-pressure suit manufactured by the David Clark Company of Worcester, Massachusetts, with an MA-3 helmet. The suit was pressurized below the neck seal with nitrogen, while the helmet was supplied with 100% oxygen. This pressure suit was later changed to the Air Force-standardized A/P22S.
North American Aviation, Inc. X-15A 56-6670 on Rogers Dry Lake, Edwards Air Force Base, California. (NASA)
The X-15 is 50.75 feet (15.469 meters) long with a wing span of 22.36 feet (6.815 meters). The height—the distance between the tips of the dorsal and ventral fins—is 13.5 feet (4.115 meters). The stabilator span is 18.08 feet (5.511 meters). The fuselage is 4.67 feet (1.423 meters) deep and has a maximum width of 7.33 feet (2.234 meters).
The X-15s were built primarily of a nickel/chromium/iron alloy named Inconel X, along with corrosion-resistant steel, titanium and aluminum. Inconel X is both very hard and also able to maintain its strength at the very high temperatures the X-15s were subjected to by aerodynamic heating. It was extremely difficult to machine and special fabrication techniques had to be developed.
X-15 56-6670 with NB-52A 52-003, 13 April 1960. (NASA)
Since the X-15 was built of steel rather than light-weight aluminum, as are most aircraft, it is a heavy machine, weighing approximately 14,600 pounds (6,623 kilograms) empty and 34,000 pounds (15,422 kilograms) when loaded with a pilot and propellants. The X-15s carried as much as 1,300 pounds (590 kilograms) of research instrumentation, and the equipment varied from flight to flight. The minimum flight weight (for high-speed missions): was 31,292 pounds (14,194 kilograms) The maximum weight was 52,117 pounds (23,640 kilograms) at drop (modified X-15A-2 with external propellant tanks).
Initial flights were flown with a 5 foot, 11 inch (1.803 meters)-long air data boom at the nose, but this would later be replaced by the “ball nose” air sensor system. The data boom contained a standard pitot-static system along with angle-of-attack and sideslip vanes. The boom and ball nose were interchangeable.
Delays in the production of the planned Reaction Motors XLR99 rocket engine forced engineers to adapt two vertically-stacked Reaction Motors XLR11-RM-5 four-chamber rocket engines to the X-15 for early flights. This was a well-known engine which was used on the previous rocketplanes. The XLR11 burned a mixture of ethyl alcohol and water with liquid oxygen. Each of the engines’ four chambers could be ignited individually. Each engine was rated at 11,800 pounds of thrust (58.49 kilonewtons) at Sea Level.
Thiokol Reaction Motors Division XLR99-RM-1 rocket engine. (U.S. Air Force)
The Reaction Motors XLR99-RM-1 rocket engine was throttleable by the pilot from 28,500 to 60,000 pounds of thrust. The engine was rated at 50,000 pounds of thrust (222.41 kilonewtons) at Sea Level; 57,000 pounds (253.55 kilonewtons) at 45,000 feet (13,716 meters), the typical drop altitude; and 57,850 pounds (257.33 kilonewtons) of thrust at 100,000 feet (30,480 meters). Individual engines varied slightly. A few produced as much as 61,000 pounds of thrust (271.34 kilonewtons).
The XLR99 burned anhydrous ammonia and liquid oxygen. The flame temperature was approximately 5,000 °F. (2,760 °C.) The engine was cooled with circulating liquid oxygen. To protect the exhaust nozzle, it was flame-sprayed with ceramic coating of zirconium dioxide. The engine is 6 feet, 10 inches (2.083 meters) long and 3 feet, 3.3 inches (0.998 meters) in diameter. It weighs 910 pounds (413 kilograms). The Time Between Overhauls (TBO) is 1 hour of operation, or 100 starts.
The XLR99 proved to be very reliable. 169 X-15 flights were made using the XLR99. 165 of these had successful engine operation. It started on the first attempt 159 times.
The highest speed achieved during the program was with the modified number two ship, X-15A-2 56-6671, flown by Pete Knight to Mach 6.70 (6,620 feet per second/4,520 miles per hour/ kilometers per hour) at 102,700 feet (31,303 meters). On this flight, the rocketplane exceeded its maximum design speed of 6,600 feet per second (2,012 meters per second).
The maximum altitude was reached by Joe Walker, 22 August 1963, when he flew 56-6672 to 354,200 feet (107,960 meters).
The longest flight was flown by Neil Armstrong, 20 April 1962, with a duration of 12 minutes, 28.7 seconds.
The North American Aviation, Inc., X-15A-1, 56-6670, being brought into the Arts and Industries building, June 1969. (Smithsonian Institution Archives SI-A-4145-23-A)
North American Aviation X-15A-1 56-6670 is on display at the Smithsonian Institution National Air and Space Museum. X-15A-2 56-6671 is at the National Museum of the United States Air Force.
North American Aviation Inc./U.S. Air Force/NASA X-15A 56-6670, hypersonic research rocketplane on display at the National Air and Space Museum. (NASM)
X-15 56-6670 is carried under the right wing of NB-52A 52-003. Scott Crossfield is in the cockpit of the rocket plane. (NASA)
17 September 1959: After previously making one glide flight, North American Aviation Chief Engineering Test Pilot Albert Scott Crossfield made the first powered flight of an X-15 hypersonic research rocket plane.
Carried aloft under the right wing of an eight-engine Boeing NB-52A Stratofortress bomber, USAF serial number 52-003, the first of three North American Aviation X-15s, 56-6670, was airdropped from 35,000 feet (10,668 meters) over Rosamond Dry Lake, west of Edwards Air Force Base. Launch time was 08:08:48.0 a.m., Pacific Daylight Savings Time (15:08.48.0 UTC).
Scott Crossfield prepares for a flight in the North American Aviation X-15A. Crossfield is wearing a conformal (face seal) helmet with his David Clark Co. MC-2 full-pressure suit. (NASA/North American Aviation, Inc.)
The X-15 was designed to use the Reaction Motors XLR-99 rocket engine, but early in the test program that engine was not yet available so two smaller XLR-11 engines were used. This was engine the same type used in the earlier Bell X-1 rocket plane that first broke the sound barrier in 1948. Though producing just one-fourth the thrust of the XLR-99, it allowed the functional testing of the X-15 to proceed.
The X-15’s two Reaction Motors XLR11 engines. (NASA)
Scott Crossfield wrote:
Two minutes after launch I reached 50,000 feet and pushed over in level flight. Then I dropped the nose slightly for a speed run, meanwhile maneuvering the ship through a series of turns and rolls, conscious of a deep rumbling noise of the rocket and a great rush of wind on the fuselage. It was obvious the black bird was in her element at supersonic speeds. She responded beautifully. I stared in fascination at the Mach meter which climbed from 1.5 Mach to 1.8 Mach and then effortlessly to my top speed for this flight of 2.3 Mach or about 1,500 miles and hour. Then, because I was under orders not to take the X-15 wide open, I shut off three of the rocket barrels. As I slowed down, I recalled the agony at Edwards many years before when we had worked for months pushing, calculating, polishing and who knows what else to achieve Mach 2 in the Skyrocket. Now with the X-15 we had reached that speed in three minutes on our first powered flight and I had to throttle back.
—Always Another Dawn, The Story Of A Rocket Test Pilot, by A. Scott Crossfield with Clay Blair, Jr., The World Publishing Company, Cleveland and New York, 1960. Chapter 39 at Pages 362.
X-15A 56-6670 drops from the wing of the B-52 mothership. The vapor trail is from hydrogen peroxide that powers the aircraft power systems. Note the roll to the right as the X-15 drops from the pylon. (NASA)
The X-15 dropped 2,000 feet (610 meters) while Scott Crossfield ignited the two XLR-11 engines and then started “going uphill.” During the 224.3 seconds burn duration, the X-15 reached Mach 2.11 (1,393 miles per hour/2,242 kilometers per hour) and climbed to 52,300 feet (15,941 meters), both slightly higher than planned.
Problems developed when the rocket engine’s turbo pump case failed, and fire broke out in the hydrogen peroxide compartment, engine compartment and in the ventral fin. Crossfield safely landed on Rogers Dry Lake at Edwards Air Force Base. The duration of the flight was 9 minutes, 11.1 seconds. Damage to the rocket plane was extensive but was quickly repaired. 56-6670 flew again 17 October 1959.
Chief Engineering Test Pilot A. Scott Crossfield climbs out of the cockpt of a North American Aviation X-15A hypersonic research rocketplane. (Der Spiegel)
Over the next nine years the three X-15s would make 199 flights, setting speed and altitude records nearly every time they flew, and expanding NASA’s understanding of flight in the hypersonic range. The first two X-15s, 56-6670 and 56-6671, survived the program. 670 is at the Smithsonian Institution National Air and Space museum and 671 is at the National Museum of the United States Air Force.
Test pilot Albert Scott Crossfield with X-15 56-6670 attached to the right wing pylon of NB-52A 52-003 at Edwards Air force Base. (North American Aviation Inc.)
