Tag Archives: Charles C. Bock Jr.

10 March 1959

North American Aviation X-15A 56-6670 carried aloft by Boeing NB-52A Stratofortress 52-003. The absence of frost on the fuselage of the X-15 shows that no cryogenic propellants are aboard for this captive flight. The chase plane is a Lockheed F-104A-15-LO Starfighter, 56-0768. This Starfighter suffered an engine failure on take off at Edwards AFB, crashed and was destroyed, 30 June 1959. (NASA)

10 March 1959: With North American Aviation’s Chief Engineering Test Pilot Albert Scott Crossfield in its cockpit, the X-15 hypersonic research rocket plane was airborne for the first time. X-15A 56-6670 was carried aloft under the wing of the Boeing NB-52A Stratofortress drop ship, 52-003, for a series of captive flights. The purpose was to verify that all the systems on both the X-15 and the B-52 were properly functioning up to the point that the drop would occur.

The NB-52A Stratofortress flight crew, left to right: Harry W. ("Bill") Berkowitz, NAA, Launch Panel Operator; Captain John E. ("Jack") Allavie, USAF, Pilot; Captain Charles C. Bock, Jr., USAF, Aircraft Commander, at Edwards AFB, 7 February 1959. (U.S. Air Force)
The NB-52A Stratofortress flight crew, left to right: Harry W. (“Bill”) Berkowitz, NAA, Launch Panel Operator; Captain John E. (“Jack”) Allavie, USAF, Pilot; Captain Charles C. Bock, Jr., USAF, Aircraft Commander, at Edwards AFB, 7 February 1959. (U.S. Air Force via Jet Pilot Overseas)
North American Aviation X-15A 56-6670 carried aloft by Boeing NB-52A Stratofortress 52-003. The absence of frost on the fuselage of the X-15 shows that no cryogenic propellants are aboard for this captive flight. (NASA)

Fully settled in my tiny flight office, I could speak by radio to the B-52 pilot, Charlie Bock, who was about thirty feet away in the nose of the mother plane, out of sight. . .

As we sat, waiting at the end of the long runway while chase planes took off and circled, the clock on the instrument panel of the X-15 showed 0955. . . On signal, B-52 pilot Charlie Bock cobbed the eight engines, standing hard on the brake pedal. As the engines wound up to full military power, the X-15 trembled and the noise was tremendous. Through my radio earphones I heard Bock call a countdown for the benefit of the official movie cameramen who would record  every inch of the takeoff:

“Five . . . four . . . three . . . two . . . one. BRAKE RELEASE.”

One hundred thirty tons of aluminum, fuel, Inconel X, five men and the hope of a nation began rolling down the long runway. . .

As we rolled, the huge runway distance markers flashed by, clocking our path: 14,000 . . . 13,000 . . . 12,000 . . . 8,000. When the X-15 air-speed indicator reached 170 knots, I noted only a minor vibration. We would continue the takeoff. 6,000 . . . 5,000 . . . 4,000, and we broke ground. It was smooth and gentle, like the take-off of an airliner. The air-speed indicator crept up to 260 knots. The parched brown desert fell away. . . .

Always Another Dawn: The Story of a Rocket Test Pilot, by A. Scott Crossfield and Clay Blair, Jr., The World Publishing Company, Cleveland and New York, 1960, Chapters 34 and 35 at Pages 316–321.

X-15A 56-6670 under the wing of NB-52A 52-003 at high altitude. Scott Crossfield is in the cockpit of the rocketplane. Air Force Flight Test Center History Office, U.S. Air Force)
X-15A 56-6670 under the wing of NB-52A 52-003 at high altitude. Scott Crossfield is in the cockpit of the rocketplane. (Air Force Flight Test Center History Office, U.S. Air Force)

The gross weight of the combined aircraft was 258,000 pounds (117,000 kilograms). After a takeoff roll of 6,200 feet (1,890 meters) the B-52/X-15 lifted of at 168 knots (193 miles per hour/311 kilometers per hour). During the 1 hour, 8 minute flight the the B-52 climbed to 45,000 feet (13,716 meters) and reached a speed of 0.83 Mach (548 miles per hour/881 kilometers per hour).

The X-15A rocketplane was designed and built for the U.S. Air Force and the National Advisory Committee for Aeronautics (NACA, the predecessor of NASA) by North American Aviation, Inc., to investigate the effects of hypersonic flight (Mach 5+). Design work started in 1955 and a mock-up had been completed after just 12 months. The three X-15s were built at North American’s Los Angeles Division, at the southeast corner of Los Angeles International Airport (LAX), on the shoreline of southern California.

Test pilot Albert Scott Crossfield with X-15 56-6670 attached to the right wing pylon of NB-52A 52-003 at Edwards Air Force Base. (North American Aviation Inc.)

The first flight took place 8 June 1959, again, with Scott Crossfield in the cockpit of the Number 1 ship, 56-6670.

While earlier rocketplanes, the Bell X-1 series, the the Douglas D-558-II, and the Bell X-2, were airplanes powered by rocket engines, the X-15 was a quantum leap in technology. It was a spacecraft.

Like the other rocketplanes, the X-15 was designed to be carried aloft by a “mothership,” rather than to takeoff and climb to the test altitude under its own power. The carrier aircraft was originally planned to be a Convair B-36 intercontinental bomber but this was soon changed to a Boeing B-52 Stratofortress. Two B-52s were modified to carry the X-15: NB-52A 52-003, The High and Mighty One, and NB-52B 52-008, Balls 8.

From 8 June 1959 to 24 October 1968, the three X-15s were flown by twelve test pilots, three of whom would qualify as astronauts in the X-15. Two would go on to the Apollo Program, and one, Neil Alden Armstrong, would be the first human to set foot on the surface of the Moon, 20 July 1969. Joe Engle would fly the space shuttle. Four of the test pilots, Petersen, White, Rushworth, and Knight, flew in combat during the Vietnam War, with Bob White being awarded the Air Force Cross. Petersen, Rushworth and White reached flag rank.

One pilot, John B. (“Jack”) McKay, was seriously injured during an emergency landing at Mud Lake, Nevada, 9 November 1962. Michael James Adams, was killed when the Number 3 ship, 56-6672, went into a hypersonic spin and broke up on the program’s 191st flight, 15 November 1967.

Scott Crossfield prepares for a flight in the North American Aviation X-15A. Crossfield is wearing a David Clark Co. MC-2 full-pressure suit and MA-3 helmet, which he helped to develop. (NASA)

Flown by a single pilot/astronaut, the X-15 is a mid-wing monoplane with dorsal and ventral fin/rudders and stabilators. The wing had no dihedral, while the stabilators had a pronounced 15° anhedral. The short wings have an area of 200 square feet (18.58 square meters) and a maximum thickness of just 5%. The leading edges are swept to 25.64°. There are two small flaps but no ailerons. The entire vertical fin/rudder pivots for yaw control.

Above 100,000 feet (30,840 meters) altitude, conventional aircraft flight control surfaces are ineffective. The X-15 is equipped with a system of reaction control jets for pitch, roll and yaw control. Hydrogen peroxide was passed through a catalyst to produce steam, which supplied the control thrusters.

The forward landing gear consists of a retractable oleo strut with steerable dual wheels and there are two strut/skids at the rear of the fuselage. The gear is retracted after the X-15 is mounted on the NB-52 and is extended for landing by its own weight.

X-15A cockpit with original Lear Siegler instrument panel. (NASA)

The rocketplane’s cockpit featured both a conventional control stick as well as side-controllers. It was pressurized with nitrogen gas to prevent fires. The pilot wore an MC-2 full-pressure suit manufactured by the David Clark Company of Worcester, Massachusetts, with an MA-3 helmet. The suit was pressurized below the neck seal with nitrogen, while the helmet was supplied with 100% oxygen. This pressure suit was later changed to the Air Force-standardized A/P22S.

The X-15 is 50.75 feet (15.469 meters) long with a wing span of 22.36 feet (6.815 meters). The height—the distance between the tips of the dorsal and ventral fins—is 13.5 feet (4.115 meters). The stabilator span is 18.08 feet (5.511 meters). The fuselage is 4.67 feet (1.423 meters) deep and has a maximum width of 7.33 feet (2.234 meters).

North American Aviation, Inc. X-15A 56-6670 on Rogers Dry Lake, Edwards Air Force Base, California. (NASA)

The X-15s were built primarily of a nickel/chromium/iron alloy named Inconel X, along with corrosion-resistant steel, titanium and aluminum. Inconel X is both very hard and also able to maintain its strength at the very high temperatures the X-15s were subjected to by aerodynamic heating. It was extremely difficult to machine and special fabrication techniques had to be developed.

Since the X-15 was built of steel rather than light-weight aluminum, as are most aircraft, it is a heavy machine, weighing approximately 14,600 pounds (6,623 kilograms) empty and 34,000 pounds (15,422 kilograms) when loaded with a pilot and propellants. The X-15s carried as much as 1,300 pounds (590 kilograms) of research instrumentation, and the equipment varied from flight to flight. The minimum flight weight (for high-speed missions): was 31,292 pounds (14,194 kilograms) The maximum weight was 52,117 pounds (23,640 kilograms) at drop (modified X-15A-2 with external propellant tanks).

Initial flights were flown with a 5 foot, 11 inch (1.803 meters)-long air data boom at the nose, but this would later be replaced by the “ball nose” air sensor system. The data boom contained a standard pitot-static system along with angle-of-attack and sideslip vanes. The boom and ball nose were interchangeable.

Two Reaction Motors Division XLR11-RM-5 four-chamber rocket engines installed on an X-15. (NASA)

Delays in the production of the planned Reaction Motors XLR99 rocket engine forced engineers to adapt two vertically-stacked Reaction Motors XLR11-RM-5 four-chamber rocket engines to the X-15 for early flights. This was a well-known engine which was used on the previous rocketplanes. The XLR11 burned a mixture of ethyl alcohol and water with liquid oxygen. Each of the engines’ four chambers could be ignited individually. Each engine was rated at 11,800 pounds of thrust (58.49 kilonewtons) at Sea Level.

The Reaction Motors XLR99-RM-1 rocket engine was throttleable by the pilot from 28,500 to 60,000 pounds of thrust. The engine was rated at 50,000 pounds of thrust (222.41 kilonewtons) at Sea Level; 57,000 pounds (253.55 kilonewtons) at 45,000 feet (13,716 meters), the typical drop altitude; and 57,850 pounds (257.33 kilonewtons) of thrust at 100,000 feet (30,480 meters). Individual engines varied slightly. A few produced as much as 61,000 pounds of thrust (271.34 kilonewtons).

The XLR99 burned anhydrous ammonia and liquid oxygen. The flame temperature was approximately 5,000 °F. (2,760 °C.) The engine was cooled with circulating liquid oxygen. To protect the exhaust nozzle, it was flame-sprayed with ceramic coating of zirconium dioxide. The engine is 6 feet, 10 inches (2.083 meters) long and 3 feet, 3.3 inches (0.998 meters) in diameter. It weighs 910 pounds (413 kilograms). The Time Between Overhauls (TBO) is 1 hour of operation, or 100 starts.

Thiokol Reaction Motors Division XLR99-RM-1 rocket engine. (U.S. Air Force)

The XLR99 proved to be very reliable. 169 X-15 flights were made using the XLR99. 165 of these had successful engine operation. It started on the first attempt 159 times.

The highest speed achieved during the program was with the modified number two ship, X-15A-2 56-6671, flown by Pete Knight to Mach 6.70 (6,620 feet per second/4,520 miles per hour/ kilometers per hour) at 102,700 feet (31,303 meters). On this flight, the rocketplane exceeded its maximum design speed of 6,600 feet per second (2,012 meters per second).

The maximum altitude was reached by Joe Walker, 22 August 1963, when he flew 56-6672 to 354,200 feet (107,960 meters).

The longest flight was flown by Neil Armstrong, 20 April 1962, with a duration of 12 minutes, 28.7 seconds.

North American Aviation X-15A-1 56-6670 is on display at the Smithsonian Institution National Air and Space Museum. X-15A-2 56-6671 is at the National Museum of the United States Air Force.

North American Aviation Inc./U.S. Air Force/NASA X-15A 56-6670 hypersonic research rocketplane on display at the National Air and Space Museum. (NASM)

© 2019, Bryan R. Swopes

23 December 1974

The first prototype Rockwell B-1A Lancer, 74-0158, takes off at AF Plant 42, Palmdale, California, 23 December 1974. (U.S. Air Force)
The first prototype Rockwell B-1A Lancer, 74-0158, takes off at Air Force Plant 42, Palmdale, California, 23 December 1974. (U.S. Air Force)

23 December 1974: The first of four prototype Rockwell B-1A Lancer Mach 2.2 strategic bombers, serial number 74-0158, made its first flight from Air Force Plant 42, Palmdale, California. The aircraft commander was company test pilot Charles C. Bock, Jr. (Colonel, U.S. Air Force, retired) with pilot Colonel Emil Sturmthal, U.S. Air Force, and flight test engineer Richard Abrams. After basic flight evaluation, the B-1A landed at Edwards Air Force Base, about 22 miles (35 kilometers) to the northeast of Palmdale.

Rockwell B-1A 74-0158 with a General Dynamics F-111 chase plane, landing at Edwards Air Force base. (U.S. Air Force)
Rockwell B-1A 74-0158 with a General Dynamics F-111 chase plane, landing at Edwards Air Force Base, California. (U.S. Air Force)

The Rockwell International B-1A Lancer was designed to operate with a flight crew of four. It was 150 feet, 2.5 inches (45.784 meters) long. With the wings fully swept, the span was 78 feet, 2.5 inches (23.838 meters), and extended, 136 feet, 8.5 inches (41.669 meters). The tip of the vertical fin was 33 feet, 7.25 inches (10.243 meters) high. The wings have an angle of incidence of 2°,  with 1° 56′ anhedral and -2° twist. The leading edges were swept to 15° when extended, and 67½°, fully swept. The total wing area is 1,946 square feet (180.8 square meters).

The empty weight of the B-1A was approximately 173,000 pounds (78,472 kilograms). The maximum takeoff weight was 389,800 pounds (176,810 kilograms), but once airborne it could take on additional fuel up to a maximum weight of 422,000 pounds (191,416 kilograms).

Rockwell International B-1A Lancer 74-0158 landing at Edwards Air Force Base. (U.S. Air Force 171219-F-ZZ999-412)

The Lancer was powered by four General Electric F101-GE-100 afterburning turbofan engines. This is an axial-flow engine with a 2-stage fan section, 9-stage compressor and 3-stage turbine (1 high- and 2 low-pressure stages). It is rated at 16,150 pounds of thrust (71.839 kilonewtons), and 29,850 pounds (132.779 kilonewtons) with afterburner. The F101-GE-100 is 15 feet, 0.7 inches (4.590 meters) long, 4 feet, 7.2 inches (1.402 meters) in diameter, and weighs 4,165 pounds (1,889 kilograms).

The bomber’s maximum speed was 1,262 knots 1,452 miles per hour/2,337 kilometers per hour)—Mach 2.2—at an optimum altitude of 53,000 feet (16,154 meters), its combat ceiling. The B-1A’s combat range was 5,675 nautical miles (6,531 statute miles/10,510 kilometers) The maximum ferry range was 6,242 nautical miles (7,183 statute miles/11,560 kilometers).

The B-1A was designed to carry 75,000 pounds (34,019 kilograms) of bombs in an internal bomb bay. It could carry a maximum of 84 MK-82 conventional explosive bombs. For a nuclear attack mission, the Lancer could carry 12 B43 free-fall bombs, or 24 B61 or B77 bombs. For a stand-off attack, the bomber could carry 24 AGM-69 SRAM (Short Range Attack Missile) nuclear missiles.

Each of the four prototypes served its own role during testing. 74-0158 was the flight evaluation aircraft.

By the time that the B-1A program was cancelled, 74-0158 had made 79 flights totaling 405.3 hours. It was dismantled and used for weapons training at Lowry Air Force Base, Colorado.

The first prototype Rockwell B-1A Lancer, 74-0158, at Edwards AFB. Visual differences of the B-1A that distinguish it from the later B-1B are the long drag link on the nose landing gear, the vertical inlet splitter vanes, black wheels and a long tail cone. On the upper fuselage behind the cockpit are the "elephant ears" intended to stabilize the crew escape capsule. (U.S. Air Force)
The first prototype Rockwell B-1A Lancer, 74-0158, at Edwards AFB. Visual differences of the B-1A that distinguish it from the later B-1B are the long drag link on the nose landing gear, the vertical inlet splitter vanes, black wheels and a long tail cone. On the upper fuselage behind the cockpit are the “elephant ears” intended to stabilize the crew escape capsule. (U.S. Air Force)

© 2018, Bryan R. Swopes