Tag Archives: Edwards Air Force Base

6 October 1961

Aviation, , , , , , , , , , , ,
Jackie Cochran with her record-setting Northrop T-38A-30-NO Talon, 60-0551, at Edwards Air Force Base, 1961. (U.S. Air Force)
Jackie Cochran with her record-setting Northrop T-38A-30-NO Talon, 60-0551, at Edwards Air Force Base, 1961. (U.S. Air Force)

6 October 1961: During a two-month series of speed, distance and altitude record attempts at Edwards Air Force Base, California, Jackie Cochran set a Fédération Aéronautique Internationale (FAI) World Record for Speed Over a Closed Circuit of 100 Kilometers Without Payload, flying a Northrop T-38A-30-NO Talon, 60-0551. Her average speed over the 62-mile circular course was 1,262.188 kilometers per hour (784.287 miles per hour).¹

Jacqueline Cochran’s Diplôme de Record in the San Diego Air and Space Museum Archives. (Bryan R. Swopes)
Jacqueline Cochran’s Diplôme de Record in the San Diego Air and Space Museum Archives. (Bryan R. Swopes)

Jackie’s friend, famed Air Force test pilot Colonel Chuck Yeager, kept notes during the series of record attempts:

September 29: Edwards AFB. Flew the aircraft today to include a practice run on the 100 kilometer course. Jackie did a fine job at 1.2 Mach. Looks like this will be a piece of cake. Aircraft was okay. Average speed 742 miles per hour. Jackie was in the altitude chamber today with the pressure suit (CSU 4/P). Everything went fine and maximum altitude was 65,000 feet. This is the first time a woman was taken up in the chamber in a pressure suit. CSU 4/P was the type of suit.

October 3: Tried a run today but weather moved in from 26,000 to 37,000 feet. Very good landing. Airspeed system iced up and Jackie stalled the aircraft at 35,000 feet. Made a no-sweat recovery.

October 4: Ran the 100 kilometer for record at 1 pm. The first run wasn’t too good but had an average speed of 763 mph. A pylon was cut so the run was voided. Second run was 740 mph. Very poor. Another flight was made at 5:30 pm but both runs were pretty sorry. Jackie was a little late on all of the corrections. Jackie doesn’t seem to be in too good a physical or mental state.

October 5: I flew in the backseat of the T-38 with Jackie on a practice run of the 100 kilometer. I talked her around the course 2 times with a little help on the stick. First run was 782 mph and second run was 787. I think I know what has been Jackie’s trouble on the 100 km. During the flight as she starts gaining a little altitude, she lets off on the back pressure on the stick to stop climbing and this causes the turn to become larger. Jackie and I spent two hours talking this over. She finally understands that in order to fly a constant circle, if the airplane starts to climb, she must increase the bank angle and let off on the back pressure a little and let the nose drop but still hold the same rate of turn. This is what makes the 100 km so hard to fly. Jackie still has a touch of the flu.

October 6: Jackie felt better today and after a delay caused by communication trouble, she flew one of the most perfect runs that has ever been flown on the 100 km course. She learned her lesson well. The record speed was 784 mph. She held 1/4 mile outside the course the entire trip. I was very pleased to watch the reaction of the timers and radar people. I think they expected another 10 or 15 trips like the F-105 tricks. She made one hell of a good flight.

— Brigadier General Charles E. Yeager, U.S. Air Force, quoted in Jackie Cochran: An Autobiography, by Jacqueline Cochran and Maryann Bucknum Brinley, Bantam Books, New York, 1987, Pages 306–307.

Jackie Cochran and Chuck Yeager at Edwards Air Force Base, California, after a flight in the record-setting Northrop T-38A Talon. (U.S. Air Force)
Jackie Cochran and Chuck Yeager at Edwards Air Force Base, California, after a flight in the record-setting Northrop T-38A Talon. (U.S. Air Force)

The Northrop T-38A Talon is a two-place, twin-engine jet trainer capable of supersonic speed. It is 46 feet, 4 inches (14.122 meters) long with a wingspan of 25 feet, 3 inches (7.696 meters) and overall height of 12 feet, 10 inches (3.912 meters). The trainer’s empty weight is 7,200 pounds (3,266 kilograms) and the maximum takeoff weight is 12,093 pounds (5,485 kilograms).

The T-38A is powered by two General Electric J85-GE-5 turbojet engines. The J85 is a single-shaft axial-flow turbojet engine with an 8-stage compressor section and 2-stage turbine. The J85-GE-5 is rated at 2,680 pounds of thrust (11.921 kilonewtons), and 3,850 pounds (17.126 kilonewtons) with afterburner. It is 108.1 inches (2.746 meters) long, 22.0 inches (0.559 meters) in diameter and weighs 584 pounds (265 kilograms).

Northrop T-38A-30-NO Talon at Edwards Air Force Base, California. (U.S. Air Force)

It has a maximum speed of Mach 1.08 (822 miles per hour, 1,323 kilometers per hour) at Sea Level. The Talon’s service ceiling of 55,000 feet (16,764 meters) and it has a maximum range of 1,093 miles (1,759 kilometers).

In production from 1961 to 1972, Northrop has produced nearly 1,200 T-38s. As of January 2014, the U.S. Air Force had 546 T-38A Talons in the active inventory. It also remains in service with the U.S. Navy, and the National Aeronautics and Space Administration.

Jackie Cochran’s record-setting T-38 is in the collection of the Smithsonian Institution, National Air and Space Museum.

Northrop T-38A Talon 60-0551, now twenty-one years old, sits on the ramp at the Sacramento Air Logistics Center, McClellan Air Force Base, Sacramento, California, 1981. (Photograph by Gary Chambers, used with permission)
Northrop T-38A Talon 60-0551, now twenty-one years old, sits on the ramp at the Sacramento Air Logistics Center, McClellan Air Force Base, Sacramento, California, 1981. (Photograph by Gary Chambers, used with permission)

¹ FAI Record File Number 13036

© 2017, Bryan R. Swopes

5 October 1954

Aviation, , , , , , , , , , , , , , ,
Lockheed XF-104 Starfighter 083-1002, serial number 53-7787, the second prototype, in flight near Edwards AFB. (U.S. Air Force)

5 October 1954: Chief Engineering Test Pilot Tony LeVier made the first flight in the second prototype Lockheed XF-104 Starfighter, 53-7787, at Edwards Air Force Base in the high desert of southern California. This was the armament test aircraft and was equipped with a General Electric T171 Vulcan 20mm Gatling gun. This six-barreled gun was capable of firing at a rate of 6,000 rounds per minute.

The XF-104 was 49 feet, 2 inches (14.986 meters) long with a wingspan of 21 feet, 11 inches (6.680 meters) and overall height of 13 feet, 6 inches (4.115 meters). The prototypes had an empty weight of 11,500 pounds (5,216 kilograms) and maximum takeoff weight of 15,700 pounds (7,121 kilograms).

While the first prototype, 53-7776, was equipped with a Buick J65-B-3 turbojet engine, the second used a Wright Aeronautical Division J65-W-6 with afterburner. Both were improved derivatives of the Armstrong Siddely Sa.6 Sapphire, built under license. The J65 was a single-shaft axial-flow turbojet with a 13-stage compressor and 2-stage turbine. The J65-B-3 was rated at 7,330 pounds of thrust, and the J65-W-6, rated at 7,800 pounds (34.70 kilonewtons), and 10,500 pounds (46.71 kilonewtons) with afterburner.

The XF-104 had a maximum speed of 1,324 miles per hour (2,131 kilometers per hour), a range of 800 miles (1,287 kilometers) and a service ceiling of 50,500 feet (15,392 meters).

53-7787 was lost 19 April 1955 when it suffered explosive decompression at 47,000 feet (14,326 meters) during a test of the T171 Vulcan gun system. The lower escape hatch had come loose due to an inadequate latching mechanism. Lockheed test pilot Herman R. (“Fish”) Salmon was unable to find a suitable landing area and ejected at 250 knots (288 miles per hour/463 kilometers per hour) and 15,000 feet (4,572 meters). The XF-104 crashed 72 miles (117 kilometers) east-northeast of Edwards Air Force Base. Salmon was found two hours later, uninjured, about 2 miles (3.2 kilometers) from the crash site.

Tony LeVier with the XF-104 armament test prototype, 53-7787, at Edwards AFB, 1954. LeVier is wearing a David Clark Co. T-1 capstan-type partial-pressure suit with K-1 helmet. (U.S. Air Force)

The YF-104A pre-production aircraft and subsequent F-104A production aircraft had many improvements over the two XF-104 prototypes. The fuselage was lengthened 5 feet, 6 inches (1.68 meters). The J65 engine was replaced with a more powerful General Electric J79-GE-3 turbojet. There were fixed inlet cones added to control airflow into the engines. A ventral fin was added to improve stability.

Lockheed F-104A-15-LO Starfighters 56-0769 and 56-0781. (Lockheed Martin)

© 2019, Bryan R. Swopes

3 October 1967

Aviation, , , , , , , , , , , , , ,
Major William J. Knight, United States Air Force, with the North American Aviation X-15A-2, 56-6671. (U.S. Air Force)

3 October 1967: The 188th flight of the X-15 Program was the 53rd for the Number 2 aircraft, 56-6671. It had been extensively modified by North American Aviation to an X-15A-2 configuration following a landing accident which had occurred 9 November 1962. The fuselage was lengthened 28 inches (0.711 meters) to accommodate a liquid hydrogen fuel tank for a scramjet engine that would be added to the ventral fin, a new tank for additional hydrogen peroxide to generate steam for the rocket engine turbo pump, and external propellant tanks to allow the rocketplane to reach higher speeds and altitudes. The entire surface of the X-15 was covered with an ablative coating to protect the metal structure from the extreme heat it would encounter on this flight.

Minor issues delayed the takeoff but finally, after they were corrected, and with Pete Knight in the X-15’s cockpit, it was carried aloft under the right wing of Balls 8, a Boeing NB-52B Stratofortress, 52-008.

At 45,000 feet (13,716 meters) over Mud Lake, Nevada, the X-15 was droppeded at 14:31:50.9 local time. Knight fired the Reaction Motors XLR99-RM-1 rocket engine and began to climb and accelerate. After 60 seconds, the ammonia and liquid oxygen propellants in the external tanks was exhausted, so the the tanks were jettisoned to eliminate their weight and aerodynamic drag.

The X-15A-2 climbed to 102,100 feet (31,120 meters) and Pete Knight leveled off, still accelerating. After 140.7 seconds of engine burn, Knight shut the XLR99 down. He noticed that thrust seemed to decrease gradually and the X-15 continued to accelerate to 6,630 feet per second (2,021 meters per second), or Mach 6.72.

North American Aviation X-15A-2 56-6671 is carried to launch altitude under the right wing of the Boeing NB-52B Stratofortress 52-008. (U.S. Air Force)
North American Aviation X-15A-2 56-6671 is carried to launch altitude under the right wing of the Boeing NB-52B Stratofortress 52-008. The scramjet is attached to the ventral fin. (U.S. Air Force)
North American Aviation X-15A-2 56-6671 immediately after being released from the mothership, Boeing NB-52B Stratofortress 52-008, Balls 8, over Mud Lake, Nevada, 3 October 1967. The steam trail is hydrogen peroxide used to power the rocket engine turbopump. (U.S. Air Force)
North American Aviation X-15A-2 56-6671 immediately after being released from the mothership, Boeing NB-52B Stratofortress 52-008, Balls 8, over Mud Lake, Nevada, 3 October 1967. The steam trail is hydrogen peroxide used to power the rocket engine turbopump. (U.S. Air Force) 
The North American Aviation X-15A-2 56-6671 ignites the XLR99 engine after being released from the mothership, Balls 8, 3 October 1967. (U.S. Air Force)
The X-15A-2’s XLR99-RM-1 rocket engine ignites after release from the mothership, Balls 8, 3 October 1967. (U.S. Air Force) 

Shock waves from the dummy scramjet mounted on the ventral fin impinged on the fin’s leading edge and the lower fuselage, raising surface temperatures to 2,700 °F. (1,482 °C.) The Inconel X structure started to melt and burn through.

Pete Knight entered the high key over Rogers Dry Lake at 55,000 feet (16,764 meters) and Mach 2.2, higher and faster than normal. As he circled to line up for Runway One Eight, drag from the scramjet caused the X-15 to descend faster and this set him up for a perfect approach and landing. Because of heat damage, the scramjet broke loose and fell away from the X-15.

Knight touched down after an 8 minute, 17.0 second flight. His 4,520 mile per hour (7,274 kilometers per hour) maximum speed is a record that still stands.

Firefighters cool down the ventral fin of the North American Aviation X-15A-2 56-6671 after its last landing on Rogers Dry Lake, 3 October 1967.(U.S. Air Force)
Firefighters cool down the ventral fin of the North American Aviation X-15A-2 56-6671 after its final landing on Rogers Dry Lake, 3 October 1967.(U.S. Air Force)

The X-15A-2 suffered considerable damage from this hypersonic flight. It was returned to North American for repairs, but before they were completed, the X-15 Program came to an end. This was 56-6671’s last flight. It was sent to the National Museum of the United States Air Force where it is part of the permanent collection.

In a ceremony at the White House, President Lyndon B. Johnson presented the Harmon International Trophy to Major William J. Knight.

The Harmon International Trophy at the Smithsonian Institution National Air and Space Museum. (NASM)
The Harmon International Trophy at the Smithsonian Institution National Air and Space Museum. (NASM)

© 2016, Bryan R. Swopes

Albert Scott Crossfield, Jr. (2 October 1921–19 April 2006)

Aviation, , , , , , , , , , , , , , , , , , , , , , , ,
Albert Scott Crossfield, aeronautical engineer and test pilot, 1921–2006. (Jet Pilot Overseas)
Albert Scott Crossfield, Jr., Aeronautical Engineer and Test Pilot, 1921–2006. (Jet Pilot Overseas)

Albert Scott Crossfield, Jr., was born at Berkeley, California, 2 October 1921, the second of three children of Albert Scott Crossfield and Lucia Dwyer Scott Crossfield. (“Scott Crossfield” is the family name, going back for many generations.) His father was a chemist who was the superintendent of the Union Oil Refinery in Wilmington, California. At the age of 5 years, the younger Scott Crossfield contracted pneumonia. He was comatose for a time and not expected to survive. When he finally began to recover, he was confined to bed for many months. The effects of this illness lasted throughout his childhood.

It was during this time that he developed his interest in aviation. He learned to draw, studied airplanes, and built scale models. Charles F. (“Carl”) Lienesch, who was a pilot for the Union Oil Company, gave Scotty his first ride aboard an airplane at age 6. As a teenager, he took flight lessons in an Inland Sportster at the Wilmington Airport.

Inland R400 Sportster NC267N, circa 1939. (William T. Larkins)

After his family bought a farm in Oregon, Scott Crossfield continued flight lessons and soloed a Curtis Robin at the age of 15. He earned his private pilot certificate at 18. After graduating from high school, “Scotty” helped his father with the family farm before attending the University of Washington as a student of aeronautical engineering. He took a job at Boeing to pay his tuition and support.

Ensign A. S. Crossfield, Jr.

After America’s entry into World War II, Scott Crossfield enlisted in the U.S. Army Air Corps as an aviation cadet, but because of expected delays in training, quickly transferred to the U.S. Navy. He enlisted as a Seaman 2/c in the Navy’s V-5 Program at the Naval Reserve Aviation Base, Seattle, Washington, on 21 February 1942. He began Primary Flight Training there, 7 May 1942. Scotty completed military flight training and was commissioned an Ensign, United States Navy, in December 1942.

On 21 April 1943, Ensign Albert Scott Crossfield, U.S. Navy, married Miss Alice Virginia Knoph at Corpus Christi, Texas.

Promoted to lieutenant (junior grade) with date of precedence 21 March 1944.

During World War II, Scott Crossfield served as a fighter pilot, flight and gunnery instructor, flying the Chance Vought F4U Corsair and Grumman F6F Hellcat. Though he was assigned to Fighting Squadron FIFTY-ONE (VF-51) aboard the Independence-class light aircraft carrier USS Langley (CVL-27), he did not serve in combat. He was promoted to the rank of lieutenant 1 August 1945. Scotty was released from active duty 31 December 1945. After the war he joined a Naval Reserve squadron and flew the Goodyear Aircraft Co. FG-1D Corsair at NAS Sand Point, Washington.

A Goodyear FG-1D Corsair, Bu. No. 92150, unfolding its wings at NAS Sand Point, circa late 1940s. The orange band around the fuselage shows that this airplane is assigned to a Naval Reserve squadron. (U.S. Navy)

During this time he resumed his education at the University of Washington and graduated with a bachelor’s degree in aeronautical engineering in 1949, and a master’s degree in 1950. As a graduate student he was the operator of the university’s Kirsten Aeronautical Laboratory wind tunnel.

The NACA High Speed Flight Station, 24 August 1954. The Boeing P2B-1S Superfortress is parked at the northeast corner of the ramp. (NASA)

In 1950 Scott Crossfield joined the National Advisory Committee for Aeronautics (NACA, the predecessor of NASA) as an Aeronautical Research Pilot at the NACA High Speed Flight Station, Edwards Air Force Base, California. He flew many high-performance jet aircraft like the North American Aviation F-100 Super Sabre, and experimental airplanes such as the Convair XF-92, Douglas X-3, Bell X-4 and X-5. He also flew the research rocket planes, making 10 rocket flights in the Bell X-1 and 77 in the Douglas D-558-II Skyrocket.

Douglas D-558-2 Bu. No. 37974 dropped from Boeing P2B-S1 Superfortress 84029, 1 January 1956. (NASA)
Douglas D-558-2 Skyrocket, Bu. No. 37974, is dropped from Boeing P2B-S1 Superfortress, Bu. No. 84029, 1 January 1956. (NASA)

On 20 November 1953, Scott Crossfield became the first pilot to fly faster than twice the speed of sound (Mach 2). The D-558-II was carried aloft by a Boeing P2B-1S Superfortress drop ship (a four-engine B-29 long range heavy bomber which had been transferred from the U.S. Air Force to the Navy, then heavily modified by Douglas) to 32,000 feet (9,754 meters) and then released. Scotty fired the LR8 rocket engine and climbed to 72,000 feet (21,945 meters). He put the Skyrocket into a shallow dive and, still accelerating, passed Mach 2 at 62,000 feet (18,898 meters). After the rocket engine’s fuel was expended, he flew the rocketplane to a glide landing on Rogers Dry Lake.

In 1955 Crossfield left NACA and joined North American Aviation, Inc., as Chief Engineering Test Pilot. He planned and participated in the design and operation of the X-15 hypersonic research rocketplane for the Air Force and NASA. He also worked closely with the David Clark Co., in the development of the project’s full-pressure suits.

Scott Crossfield testing an experimental David Clark Co. XMC-2 full-pressure suit in a thermal chamber at Wright Field. (Ralph Morse, LIFE Magazine/National Archives College Park Collection)

Milton O. Thompson, another X-15 test pilot, wrote in At the Edge of Space,

“. . . he was intimately involved in the design of the aircraft and contributed immensely to the success of the design, as a result of his extensive rocket airplane experience. . . Scott was responsible for a number of other excellent operational and safety features built into the aircraft. Thus, one might give Scott credit for much of the success of the flight program. . . .”

—At the Edge of Space, by Milton O. Thompson, Smithsonian Institution Press, Washington and New York, 1992, at Page 3

Scott Crossfield, NAA Chief Engineering Test Pilot; Edmond Ross Cokeley, NAA Director of Flight Test;  and Charles H. Feltz, NAA Chief Engineer, with an X-15 hypersonic research rocketplane. (North American Aviation via Jet Pilot Overseas)

In 1959–1960, Scott Crossfield flew all of the contractor’s demonstration phase flights for the X-15, including 16 captive carry flights under the wing of the NB-52A Stratofortress while systems were tested and evaluated, one glide flight, and thirteen powered flights. He reached a a maximum altitude of 88,116 feet (26,858 meters) on Flight 6, and a maximum speed of Mach 2.97 (1,960 miles per hour/3,154 kilometers per hour) on Flight 26. The X-15 was then turned over to NASA and the Air Force. The X-15 Program involved a total of 199 flights from 1959 until 1968.

A. Scott Crossfield, wearing a David Clark Co. XMC-2 full-pressure suit, which he helped to design and test, with the first of three North American X-15s, 56-6670. (North American Aviation, Inc.)

After leaving the X-15 Program, Scott Crossfield continued as a Systems Director with North American Aviation, Inc., working on the Apollo Command and Service Module and the S-IVB second stage of the Saturn V rocket. He left North American in the late ’60s and served as an executive with Eastern Air Lines and Hawker Siddeley. He also continued as a aeronautical engineering consultant to private industry and government.

Among many other awards, Scott Crossfield was received the Harmon Trophy, the Collier Trophy, and the Iven C. Kincheloe Award of the Society of Experimental Test Pilots..

Scott Crossfield's 1962 Cessna 210A Centurion, photographed at Santa Monica Airport, California, 26 September 1999. (AirNikon Collection, Pima Air & Space Museum, Tucson, Arizona via airliners.net)
Scott Crossfield’s Cessna 210A Centurion, N6579X, photographed at Santa Monica Airport, California, 26 September 1999. (AirNikon Collection, Pima Air & Space Museum, Tucson, Arizona via airliners.net, used with permission)

In 1980 Crossfield resumed flying when he purchased a 1960 Cessna 210A Centurion, N6579X, serial number 21057579. This was a single-engine, four-place light airplane, powered by an air-cooled Continental six-cylinder engine. He had flown more than 2,000 hours in this airplane when it crashed during a severe thunderstorm, 19 April 2006, while on a flight from Prattville, Alabama, to Manassas, Virginia.

Albert Scott Crossfield, Jr., was killed. His remains are interred at the Arlington National Cemetery, Arlington, Virginia.

Albert Scott Crossfield, Jr., Test Pilot. (LIFE Magazine via Jet Pilot Overseas)

Highly recommended: Always Another Dawn: The Story Of A Rocket Test Pilot, by Albert Scott Crossfield and Clay Blair, Jr., The World Publishing Company, Cleveland and New York, 1960.

© 2018, Bryan R. Swopes

1 October 1947

Aviation, , , , , , , , , , , , , ,
North American Aviation test pilot George S. Welch, flying the first of three XP-86 prototypes, serial number 45-59597. (North American Aviation, Inc.)

1 October 1947: After three years development in which 801,386 engineering hours and 340,594 drafting hours had been expended, the first prototype North American Aviation XP-86 (company designation NA-140), serial number 45-59597, was ready for its first flight at Muroc Dry Lake in the high desert, north of Los Angeles, California.

Completed at North American’s Inglewood plant on 8 August 1947, it was trucked to Muroc in mid-September. It was reassembled, everything was checked out, and after a few taxi tests, company test pilot George S. Welch took off for a initial familiarization flight. Chief Test Pilot Bob Chilton flew chase in an XP-82 Twin Mustang with a company photographer on board. The duration of the first flight was 1 hour, 18 minutes.

Recently completed, the first prototype XP-86, 45-59597, waits inside the North American Aviation plant at Inglewood, California, 14 August 1947. (North American Aviation, Inc.)

During this first flight, George Welch climbed to 35,000 feet (10,668 meters):

“In a little more than ten minutes he had reached 35,000 feet. Leveling out, the test pilot smiled as he watched the indicated airspeed accelerate to 320 knots. He estimated that should be 0.90 Mach number. . . Rolling into a 40 degree dive, he turned west. . . The airspeed indicator seemed to be stuck at about 350 knots. The Sabre was behaving just fine. Then at 29,000 feet, there was a little wing roll. Correcting the roll, George pushed into a steeper dive. The airspeed indicator suddenly jumped to 410 knots and continued to rise. At 25,000 feet, he pulled the Sabre into level flight and reduced power. The wing rocked again and the airspeed jumped back to 390.”

—Aces Wild: The Race for Mach 1, by Al Blackburn, Scholarly Resources Inc., Wilmington, Delaware, 1998, at Chapter 5, Pages 144–145.

George Welch was the first to report instrument readings that would be referred to as “Mach jump.” It has been argued that George Welch flew the XP-86 beyond Mach 1 during this flight, breaking the “sound barrier” two weeks before Chuck Yeager did with the Bell X-1 rocketplane. During flight testing, it was firmly established that the XP-86 could reach Mach 1.02–1.04 in a dive, so it is certainly possible that he did so on the Sabre’s first flight.

North American Aviation Model NA-140, the first XP-86 prototype, 45-59597, at Muroc AAF, 1947. (U.S. Air Force)
North American Aviation Model NA-140, the first XP-86 prototype, 45-59597, at Muroc AAF, 1947. (U.S. Air Force)

The XP-86 was unlike any airplane before it. It was the first airplane with a swept wing. After analyzing test data from the Messerschmitt Me 262, North American’s engineers designed a wing with a 35° degree sweepback to its leading edge. The wing tapered toward the tips, and its thickness also decreased from the root to the tip. In order to create a very strong but very thin wing, it was built with a two-layered aluminum skin, instead of ribs and spars, with each layer separated by “hat” sections. The wing sweep allowed high speed shock waves to form without stalling the entire wing.

Cutaway illustration of the XP-86. The speed brake configuation was not used for production aircraft. (North American Aviation, Inc.)

The wing also incorporated leading edge “slats” which were airfoil sections that automatically extended below 290 knots, smoothing the air flow over the wing’s upper surface and creating more lift at slow speeds. Above that speed, aerodynamic forces closed the slats, decreasing drag and allowing for higher speeds. Effectively, the wing could change its shape in flight.

Test pilot George S. Welch, wearing his distinctive orange helmet, in the cockpit of the prototype XP-86. This photograph was taken 14 October 1947. (U.S. Air Force)
This photograph of the XP-86 shows the 35° wing sweep. Test pilot George S. Welch, wearing his distinctive orange helmet, in the cockpit of the prototype XP-86. (North American Aviation, Inc.)

The XP-86 prototypes were 37 feet, 6½ inches (11.443 meters) long with a wingspan of 37 feet, 1–7/16 inches (11.314 meters) and overall height of 14 feet, 9 inches (4.496 meters). The empty weight was 9,730 pounds (4,413.5 kilograms), gross weight, 13,395 pounds (6,075.9 kilograms) and maximum takeoff weight was 16,438 pounds (7,456.2 kilograms).

North American Aviation XP-86 45-59597. (Ray Wagner Collection, San Diego Air & Space Museum Archives, Catalog #: 16_002950)

The XP-86 was initially powered by a General Electric-designed, Chevrolet-built J35-C-3 turbojet which produced 4,000 pounds of thrust. This was soon changed to an Allison J35-A-5. Performance testing was conducted with the Allison engine installed. The J35 was a single-spool, axial-flow turbojet engine with an 11-stage compressor and single-stage turbine. The J35-A-5 was rated at 4,000 pounds of thrust (17.79 kilonewtons) at 7,700 r.p.m. (static thrust, Sea Level). The engine was 14 feet, 0.0 inches (4.267 meters) long, 3 feet, 4.0 inches (1.016 meters) in diameter and weighed 2,400 pounds (1,089 kilograms).

The three North American Aviation XP-86 prototypes. Front to back, 45-59598, 45-59597 and 45-59599. (National Archives and Records Administration)

The maximum speed of the XP-86 at Sea Level was 0.787 Mach (599 miles per hour, 964 kilometers per hour), 0.854 Mach (618 miles per hour, 995 kilometers per hour) at 14,000 feet (4,267 meters) and 575 miles per hour (925 kilometers per hour) at 35,000 feet (10,668 meters)—0.875 Mach.

The prototype fighter was able to take off at 125 miles per hour (201 kilometers per hour) in just 3,020 feet (920.5 meters) of runway. It could climb to 30,000 feet (9,144 meters) in 12.1 minutes and had a service ceiling of 41,300 feet (12,588 meters).

The end of XP-86 45-59597 at Frenchman Flats, 1953.

XP-86 45-59597 was expended as a target during nuclear weapons tests. On 25 May 1953, it was 1,850 feet from ground zero of Upshot Knothole Grable. The only part still intact was the engine, which was thrown 500 feet.

Upshot Knothole Grable (National Nuclear Security Administration CIC 0315864)
George S. Welch, North American Aviation test pilot, wearing his orange flight helmet. An F-86 Sabre is in the background. (San Diego Air and Space Museum Photo Archives)

George Welch was born George Lewis Schwartz, in Wilmington, Delaware, 10 May 1918. His parents changed his surname to Welch, his mother’s maiden name, so that he would not be effected by the anti-German prejudice that was widespread in America following World War I. He studied mechanical engineering at Purdue, and enlisted in the Army Air Corps in 1939.

George S. Welch is best remembered as one of the heroes of Pearl Harbor. He was one of only two fighter pilots to get airborne during the Japanese surprise attack on Hawaii, 7 December 1941. Flying a Curtiss P-40B Warhawk, he shot down three Aichi D3A “Val” dive bombers and one Mitsubishi A6M2 Zero fighter. For this action, Lieutenant General H.H. “Hap” Arnold recommended the Medal of Honor, but because Lieutenant Welch had taken off without orders, an officer in his chain of command refused to endorse the nomination. He received the Distinguished Service Cross.

During World War II, George Welch flew the Bell P-39 Airacobra and Lockheed P-38 Lightning on 348 combat missions. He had 16 confirmed aerial victories over Japanese airplanes and rose to the rank of Major.

Suffering from malaria, George Welch was out of combat, and when North American Aviation approached him to test the new P-51H Mustang, General Arnold authorized his resignation. Welch test flew the P-51, FJ-1 Fury, F-86 Sabre and F-100 Super Sabre. He was killed 12 October 1954 when his F-100A Super Sabre came apart in a 7 G pull up from a Mach 1.5 dive.

North American Aviation F-86-A-NA Sabre 47-630. (North American Aviation, Inc./Chicago Tribune)
An early production aircraft, North American Aviation P-86A-1-NA Sabre 47-630 (s/n 151-38457). (North American Aviation, Inc./Chicago Tribune)

After testing, the North American Aviation XP-86 was approved for production as the F-86A. It became operational in 1949. The first squadron to fly the F-86 held a naming contest and from 78 suggestions, the name “Sabre” was chosen. The F-86 Sabre was in production until 1955 at North American’s Inglewood, California, and Columbus, Ohio, plants. It was also built under license by Canadair, Ltd., Sain-Laurent, Quebec, Canada; the Commonwealth Aircraft Corporation, Port Melbourne, Victoria, Australia; and Mitsubishi Heavy  Industries at Nagoya, Aichi Prefecture, Japan. A total of 9,860 Sabres were built. They served with the United States Air Force until 1970.

XP-86 45-59597 was expended in nuclear weapons tests, Operation Snapper Easy and Snapper Fox, at the Nevada Test Site, Frenchman’s Flat, Nevada, in May 1952. The second and third prototypes, 45-59598 and 45-59599, met similar fates.

© 2017, Bryan R. Swopes