Tag Archives: First Flight

20 December 1957

Aviation, , , , , , , , , , , , , , ,
Boeing 707-121 N708PA, photographed during its second flight. (Boeing via Space.com)
Boeing 707-121 N708PA, photographed during its second flight on the afternoon of 20 December 1957. (Boeing)
Boeing 707-121 N708PA makes its first takeoff at 12:30 p.m., on a rainy afternoon, 20 December 1957. (Unattributed)
Boeing 707-121 N708PA makes its first takeoff at 12:30 p.m. on a rainy afternoon, 20 December 1957. (Boeing)

20 December 1957: The first production Boeing 707 jet-powered commercial airliner, N708PA, made its first flight at Renton, Washington. Alvin M. “Tex” Johnston, Boeing’s Chief of Flight Test, was in command, with co-pilot James R. Gannet and flight engineer Tom Layne. Takeoff was at 12:30 p.m., PST. Poor weather limited the first flight to just 7 minutes. The new airliner landed at Boeing Field. Later that day, a second flight was made, this time with a duration of 1 hour, 11 minutes.

N708PA (Serial Number 17586, Line Number 1) was a Model 707-121. The new airliner had been sold to Pan American World Airways, the launch customer, as part of an order for twenty 707s in October 1955.

Boeing test pilot Alvin M. "Tex" Johnston in the cockpit of of the 367–80. (LIFE)
Boeing’s Chief of Flight Test, Alvin M. “Tex” Johnston, in the cockpit of of the 367–80, “Dash Eighty,” 1954. (LIFE Magazine via Jet Pilot Overseas)

The Boeing Model 707 was developed from the earlier Model 367–80, the “Dash Eighty,” prototype for an air-refueling tanker which would become the KC-135A Stratotanker. The 707 was a four-engine jet transport with swept wings and tail surfaces. The leading edge of the wings were swept at a 35° angle.

N708PA was initially used for flight testing by Boeing. Once this was completed, it was prepared for commercial service and delivered to Pan American at San Francisco International Airport (SFO), 30 November 1958. Pan Am named the new airliner Clipper Constitution.

Boeing 707-121 708PA under maintenance at Renton, Washington. (Boeing)
Boeing 707-121 N708PA under maintenance at Renton, Washington. (Boeing)

In February 1965, the airliner was upgraded to 707-121B standards, which replaced the original turbojet engines with quieter, more efficient Pratt & Whitney JT3D-1 turbofan engines which produced 17,000 pounds of thrust. The wing inboard leading edges were modified to the design of the Model 720 and there was a longer horizontal tail plane.

Clipper Constitution flew for Pan Am for nearly seven years, until 17 September 1965 when it crashed into Chances Peak, a 3,002 foot (915 meters) volcano on the Caribbean island of Montserrat. The point impact  was 242 feet (74 meters) below the summit. All aboard, a crew of 9 and 21 passengers, were killed.

Boeing 707-121 N708PA, with both Boeing and Pan American corporate markings. (Unattributed)
Boeing 707-121 N708PA, with both Boeing and Pan American corporate markings. (Unattributed)

The Boeing Model 707-121 was a four-engine jet transport with swept wings and tail surfaces. The leading edge of the wings were swept at a 35° angle. The airliner had a flight crew of four: pilot, co-pilot, navigator and flight engineer.

The 707-121 was 145 feet, 1 inch (44.221 meters) long with a wing span of 130 feet, 10 inches (39.878 meters). The top of the vertical fin stood 42 feet, 5 inches (12.929 meters) high. The 707 pre-dated the ”wide-body” airliners, having a fuselage width of 12 feet, 4 inches (3.759 meters). The airliner’s empty weight is 122,533 pounds (55,580 kilograms). Maximum take off weight is 257,000 pounds (116,573 kilograms).

The first versions were powered by four Pratt & Whitney Turbo Wasp JT3C-6 turbojet engines, producing 11,200 pounds of thrust (49,820 kilonewtons), and 13,500 pounds (60.051 kilonewtons) with water injection. This engine was a civil variant of the military J57 series. It was a two-spool axial-flow turbojet engine with a 16-stage compressor and 2 stage turbine. The JT3C-6 was 11 feet, 6.6 inches (3.520 meters) long, 3 feet, 2.9 inches (0.988 meters) in diameter, and weighed 4,235 pounds (1,921 kilograms).

At MTOW, the 707 required 11,000 feet (3,352.8 meters) of runway to take off.

The 707-121 had a maximum speed of 540 knots (1,000 kilometers per hour). It’s range was 2,800 nautical miles (5,186 kilometers).

The Boeing 707 was in production from 1958 to 1979. 1,010 were built. Production of 707 airframes continued at Renton until the final one was completed in April 1991. As of 2011, 43 707s were still in service.

Boeing 707-121 N708PA retracts its landing gear after taking off at Seattle Tacoma Airport. (Unattributed)
Boeing 707-121 N708PA retracting its landing gear after takeoff at Seattle Tacoma Airport. (Unattributed)

© 2016, Bryan R. Swopes

20 December 1934

Aviation, , , , , , ,
“This photograph of the Clipper, aloft at the mouth of the Middle River, was taken from another plane by Robert F. Kniesche, Sun staff photographer.” (The Sun (Baltimore), Vol. 196–D, Friday 21 December 1934, Page 30, Columns 3–5 )

20 December 1934: William K. (“Ken”) Ebel lifted off from Middle River, Maryland, taking the Martin M-130 “Clipper” for its first flight. The M-130 was airborne for approximately 1 hours. Flying at 1,200 feet (366 meters), it reached 160 miles per hour (257 kilometers per hour).

Three-view illustration of the Martin M-130. (Flight, The Aircraft Engineer & Airships, Vol. XXVII, No. 1361, 24 January 1935, Page 99)

NC14716, named China Clipper, was the first of three Martin M-130 four-engine flying boats built for Pan American Airways. It was used to inaugurate the first commercial transpacific air service from San Francisco to Manila in November, 1935. Built at a cost of $417,000 by the Glenn L. Martin Company in Baltimore, Maryland, it was delivered to Pan Am on October 9, 1935.

The airplane was operated by a flight crew of 6 to 9, depending on the length of the flight, plus cabin staff, and could carry 18 passengers on overnight flights or a maximum 36 passengers.

Cutaway illustration of Pan American Airways’ Martin M-130 China Clipper. (Detail from larger image. NASM SI-89-1216-A. Full image at: https://airandspace.si.edu/multimedia-gallery/7135hjpg)

The Martin M-130 was 90 feet, 10.5 inches (27.699 meters) long with a wingspan of 130 feet, 0 inches (39.624 meters). It was 24 feet, 7 inches (7.493 meters) high. The total wing area was 2,315 square feet (215 square meters), including the “sea wings”. Its maximum takeoff weight was 52,252 pounds (23,701 kilograms).

Martin M-130 under construction, 24 May 1934. (SFO Museum)

The flying boat was powered by four air-cooled, supercharged Pratt & Whitney Twin Wasp S2A5-G two-row 14-cylinder radial engines with a compression ratio of 6.7:1. They had a normal power rating 830 horsepower at 2,400 r.p.m., and 950 horsepower at 2,550 r.p.m. for takeoff. They drove three-bladed Hamilton Standard Hydromatic constant-speed propellers through a 3:2 gear reduction. The S2A5-G was 3 feet, 11.88 inches (1.216 meters) in diameter, 4 feet, 8.75 inches (1.441 meters) long, and weighed 1,235 pounds (560 kilograms).

The airplane had a cruise speed of 130 miles per hour (209 kilometers per hour) and a maximum speed of 180 miles per hour (290 kilometers per hour). The M-130’s service ceiling was 10,000 feet (3,048 meters). Its range was 3,200 miles (5,150 kilometers).

A Martin M-130, X14714, undergoing ground testing at the Glenn L. Martin Co. plant at Middle River, Maryland, 30 November 1934. (Lockheed Martin)
Martin M-130 X14714, 30 November 1934. (SFO Museum)

William Kenneth Ebel was born at Orangeville, Illinois, 2 January 1899. He was the first of two sons of Willam Henry Ebel, a farmer, and Nora Agnes Rubendall Ebel.

Ken Ebel attended Heidelberg College at Tiffin, Ohio. While at Heidelberg, on 1 October 1918, he enlisted as a private in the Student Army Training Corps (S.A.T.C.). With World War I coming to an end in November, Private Ebel was discharged 20 December 1918. Ebel graduated from Heidelberg in 1921 with a bachelor of arts degree.

Ebel returned to military service, enlisting as a private in the 104th Squadron (Observation), Maryland National Guard, based at Baltimore, Maryland.

Ebel continued his college education at the Case School of Applied Science in Cleveland, Ohio. In 1923, he earned a bachelor of science degree in mechanical engineering (B.S.M.E.)

On 11 September 1923, Private Ebel was appointed an aviation cadet, graduating from primary flying school on 3 June 1924. He received a commission as a 2nd lieutenant, Officers Reserve Corps (O.R.C.), United States Army, on 12 June 1925.

Continuing to serve as a reserve officer, in 1926 Ebel went to work as an engineer for the Glenn L. Martin Company, then located in Cleveland, Ohio. As a test pilot and engineer, Ebel flew the Martin M-130 four-engine flying boar

2nd Lieutenant Ebel,still with the 104th Squadron, Maryland National Guard, was promoted to the rank of 1st lieutenant on 21 December 1928. The U.S. Army advanced his rank to 1st lieutenant, Air Corps, 15 February 1929.

On 21 October 1929, William K. Ebel married Miss Florence E. Sherck at Seneca, Ohio. They would have two children, William Kenneth, Jr., and Lydia Lynn Ebel.

While testing a Martin BM-2 dive bomber, on 11 August 1932, W.K. Ebel “leaped to safety in a parachute Friday when a bombing plane he was testing failed to come out of a spin and crashed at Dahlgren, Virginia. The plane was going through its final tests before being delivered to the navy. It was wrecked in the crash.” Ebel became Member No. 495 of The Caterpillar Club.

On Thursday, 20 December 1934, Chief Pilot Ken Ebel took the new four-engine Martin M-130 flying boat, Pan American Airways System’s Hawaii Clipper, for its first flight from Middle River, Maryland. He also made the first flight of the M-156 “Russian Clipper” in 1935.

Ebel was promoted to captain, Air Corps, on 5 January 1935. On 21 August, he delivered the new Martin Model 146 “mystery bomber” to Wright Field for evaluation by the Bombardment Board.

In 1948, Ken Ebel became director of the Airplane Division of the Curtiss-Wright Corporation in Columbus, Ohio. Soon after, Curtiss-Wright sold its airplane division to North American Aviation. In 1950, the U.S. Navy’s primary submarine builder, the Electric Boat Company, appointed Ebel as Vice Pressident of Engineering for its Canadair Ltd., aircraft manufacturing subsidiary in Montreal, Quebec, Canada. (In 1952, after acquiring Convair, the corporation reorganized as General Dynamics.

William K. Ebel

Ebel returned to the United States in 1961 and served as a consultant for General Dynamics in Washington, D.C. Ebel retired in 1963, purchasing the Mount Pleasant Orchards near Baltimore.

Mrs. Ebel died in 1968. He later married Helene H. Topping.

William Kenneth Ebel, Ph.D., died at the Greater Baltimore Medical Center, 12 July 1972.

© 2019, Bryan R. Swopes

18 December 1953

Aviation, , , , , , , , , , , ,
Sikorsky XHR2S-1, Bu. No. 133732, the first Model S-56, hovers at Sikorsky Aircraft, Bridgeport, Connecticut. (Sikorsky Historical Archives)

18 December 1953: At Bridgeport, Connecticut, Sikorsky chief test pilot Dimitry D. (“Jimmy”) Viner and co-pilot James Edward Chudars made the first flight of the Sikorsky XHR2S-1 (Sikorsky Model S-56). The XHR2S-1 was a prototype assault and heavy-lift helicopter for the United States Navy and Marine Corps. It was later adopted by the U.S. Army as the H-37 Mohave.

The S-56 was a large twin-engine helicopter, following the single main rotor/tail (anti-torque) rotor configuration pioneered by Sikorsky with the Vought-Sikorsky VS-300 in 1939. The helicopter was designed to be flown by two pilots in a cockpit located above the main cabin. The two engines were placed in nacelles outboard of the stub wings which also housed the helicopter’s retractable main landing gear. Two large clam shell cargo doors and loading ramp were placed in the nose. The HR2S-1 incorporated a stability system and an automatic torque compensating tail rotor.

The S-56 series was the largest and fastest helicopter built up to that time, and remains the largest reciprocating engine helicopter ever built.

U.S. Marine Corps HR2S-1 Bu. No. 138423, the seventh production S-56 helicopter (Sikorsky Historical Archives)

The S-56 was equipped with a five blade articulated main rotor. This allowed increased lift and higher forward air speed before encountering retreating blade stall than earlier three and four blade systems. A six blade rotor system was tested, which showed further improvements, but was not adopted. The main rotor diameter was initially 68 feet (20.726 meters), but later increased to 72 feet (21.946 meters). The main rotor blades had a chord of 1 foot, 9.5 inches (0.546 meters) and used the symmetrical NACA 0012 airfoil, which was standard with American helicopters up to that time. Later in the program, the blades were lengthened and the chord increased to 1 foot, 11.65 inches (0.601 meters). The airfoil was changed to the NACA 0010.9 airfoil. These changes resulted in increased lift and higher speed. The four blade tail rotor had a diameter of 15 feet (4.572 meters). The individual blades had a chord of 1 foot, 1.5 inches (0.343 meters). As is common with American helicopters, the main rotor system turned counter-clockwise as seen from above. (The advancing blade is on the right.) The tail rotor turned counter-clockwise when viewed from the helicopter’s left side. (The advancing blade is above the axis of rotation.)

Sikorsky S-56 three-view illustration with dimensions. (Sikorsky Historical Archives)

With the longer blades installed, the helicopter’s length with rotors turning was 88 feet (26.822 meters). The fuselage had a length of 64 feet, 10.69 inches (19.779 meters), and the height was 17 feet, 2 inches (5.232 meters). The HR2S-1 had an empty weight of 21,502 pounds (9,753 kilograms), and maximum weight (overload) of 31,000 pounds (14,061 kilograms). Its fuel capacity was 1,000 U.S. gallons (3,785 liters) carried in 6 tanks located in the nacelles, wings and fuselage. It could carry 20 fully-equipped troops, or 16 litters. Its maximum cargo capacity was 10,000 pounds (4,536 kilograms).

The HR2S-1 had an automatic main rotor blade folding system, and its tail rotor pylon could be folded alongside the fuselage, reducing the length to 55 feet, 8 inches (16.967 meters) and width to 27 feet, 4 inches (8.331 meters). This allowed the helicopter to use aircraft carrier elevators and reduced storage space on the hangar deck.

Early S-56 models were powered by two air-cooled, supercharged 2,804.461 cubic inch displacement (45.957 liters) Pratt & Whitney Double Wasp R-2800-50 two-row, 18-cylinder radial engines rated at 1,900 horsepower at 2,500 r.p.m. These were upgraded in later models to R-2800-54s. These were direct drive engines with a compression ratio of 6.75:1. The R-2800-54 was rated at 2,100 horsepower at 2,700 r.p.m. to 5,000 feet (1,524 meters) for takeoff; with a normal power rating of 1,900 horsepower at 2,600 r.p.m. to 7,000 feet (2,134 meters). It required 115/145 octane aviation gasoline. Each engine was supplied with 13.3 gallons (50.35 liters) of lubricating oil. The R-2800-54 was 6 feet, 9.00 inches long (2.057 meters), 4 feet, 5.00 inches (1.346 meters) in diameter, and weighed 2,300 pounds (1,043 kilograms).

The helicopter’s engines were installed at an 80° angle to the aircraft center line, with a 12.5° upward angle to align with the main transmission input. The front of the engines faced inboard. According to Sikorsky, this unusual installation resulted in high oil consumption, and because the engines were operated at continuous high r.p.m., the time interval between engine overhauls was reduced from the normal 2,000 hours to just 350 hours.

Two U.S. Marine Corps HR2S-1 Mohave assault helicopters of Marine Helicopter Transport Squadron (HMR) 462 at Camp Pendelton, California, late 1950s. (Naval History and Heritage Command)

The production HR2S-1 had a cruise speed of 100 knots (115 miles per hour/185 kilometers per hour), and a maximum speed of 121 knots (139 miles per hour/224 kilometers per hour) at Sea Level. The helicopter’s service ceiling was 13,800 feet (4,206 meters), and its absolute hover ceiling was 5,400 feet (1,646 meters). It had a maximum rate of climb of 1,580 feet per minute (8.03 meters per second) at Sea Level, and a vertical rate of climb 950 feet per minute (4.83 meters per second), also at Sea Level. The combat radius of the HR2S-1 was 100 nautical miles (115 statute miles/185 kilometers) at 100 knots (115 miles per hour/185 kilometers per hour.)

55 HR2S-1s were delivered to the U.S. Marine Corps. The U.S. Army purchased 94 S-56s in the H-37A Mohave configuration. 90 of these were later returned to Sikorsky to be upgraded to H-37Bs. This added the automatic stabilization system of the HR2S-1, changed the variable incidence horizontal stabilizers on both side of the fuselage to a single stabilizer on top of the tail rotor pylon. Engine oil capacity was increased to 30 gallons (113.6 liters) per engine.

A total of 154 S-56s were built between 1953 and 1960.

U.S. Marines exit the front cargo doors of a Sikorsky XHR2S-1 helicopter during a demonstration at Bridgeport, Connecticut, circa 1953. The leading Marine is carrying an M1918 .30-caliber Browning Automatic Rifle (commonly known as the “B-A-R”), while those following are armed with the M1 “Garand” .30-caliber semi-automatic rifle. Note the cinematographer behind the starboard cargo door. (National Archives and Records Administration, NAID: 74241875)

From 9 through 11 November 1956, a U.S. Marine Corps HR2S-1 flown by Major Roy Lee Anderson, USMC, and Sikorsky test pilot Robert S. Decker at Windsor Locks, Connecticut,  set three Fédération Aéronautique Internationale (FAI) world records for speed and payload:

On 9 November, the helicopter reached an altitude of 3,722 meters (12,211 feet) with a payload of 5,000 kilograms (11,023 pounds).¹ The following day, 10 November, it set a record for the greatest mass carried to a height of 2,000 meters (6562 feet): 6,010 kilograms (13,250 feet).² Then on 11 November, the HR2S-1 reached a speed of 261.91 kilometers per hour (162.74 mph) over a  3-kilometer (1.86 miles) course.³ For these flights, Major Anderson was awarded a third gold star in lieu of a fourth award of the Distinguished Flying Cross.

Major Roy Lee Anderson, USMC, (left) and Sikorsky test pilot Robert Stewart Decker. (Fédération Aéronautique Internationale)
The world-record-setting Sikorsky HR2S-1. Note the dorsal filet. (Fédération Aéronautique Internationale)

¹ FAI Record File Number 13129

² FAI Record File Number 13124

³ FAI Record File Number 13098

© 2023, Bryan R. Swopes

17 December 1947

Aviation, , , , , , , , , , , , , ,
Boeing XB-47 Stratojet 46-065 in flight over a snow-covered landscape. (U.S. Air Force)
Boeing XB-47 Stratojet 46-065 in flight over a snow-covered landscape. (U.S. Air Force)
Robert M. Robbins
Robert M. Robbins

17 December 1947: Boeing test pilots Robert M. Robbins and Edward Scott Osler made the first flight of the Model 450, the XB-47 Stratojet prototype. It was a 52-minute flight from Boeing Field, Seattle, to Moses Lake Air Force Base, five miles north of the town of Moses Lake, Washington.

Robbins later said, “The best way to tell about the performance of the Stratojet is to say that any good crew could have flown it. It took no unusual ability or education. Neither Scott Osler nor I deserve any credit for the flight. Rather, the credit should go to the men who carried out these visions on the drafting boards and the factory workers who made the visions a reality.”

On 11 May 1949, during flight testing at Moses Lake, the canopy of 46-065 came off, killing test pilot Scott Osler. The co-pilot safely landed the airplane.

Designed as a strategic bomber, the B-47 could fly higher and faster than jet fighters of the time, and it was also highly maneuverable. The XB-47 (Boeing Model 450) was flown by a two-man crew in a tandem cockpit. It was 107 feet, 6 inches (32.766 meters) long with a wingspan of 116 feet (35.357 meters). The top of the vertical fin was 27 feet, 8 inches (8.433 meters) high. The wings were shoulder-mounted with the leading edges swept at 35°.

Boeing XB-47 Stratojet 46-065. (U.S. Air Force 061024-F-1234S-004)

The first prototype, 46-065, was powered by six General Electric J35-GE-7 axial flow turbojet engines in four pods mounted on pylons below the wings. The J35 was a single-spool, axial-flow turbojet engine with an 11-stage compressor and single-stage turbine. The J35-GE-7 was rated at 3,750 pounds of thrust (16.68 kilonewtons) at 7,700 r.p.m. (static thrust, Sea Level). The engine was 14 feet, 0.0 inches (4.267 meters) long, 3 feet, 4.0 inches (1.016 meters) in diameter and weighed 2,400 pounds (1,089 kilograms). (The second prototype, 46-066, was completed with J47 engines. 46-065 was later retrofitted with these engines.)

The XB-47 prototype had a maximum speed of 502 knots (578 miles per hour/930 kilometers per hour/0.80 Mach) at 15,000 feet (4,572 meters). The combat speed was 462 knots (532 miles per hour/856 kilometers per hour/0.70 Mach) at 35,000 feet (10,668 meters). The prototype’s empty weight was 74,623 pounds (33,848 kilograms), while its maximum takeoff weight was 162,500 pounds (73,709 kilograms). It required a ground run of 11,900 feet (3,627 meters), or 4,800 feet (1,463 meters) with JATO assist. The bomber could climb at a rate of 3,650 feet per minute (18.5 meters per second) at Sea Level, at combat weight and maximum power. The service ceiling was 37,500 feet (11,430 meters). The XB-47 carried 9,957 gallons (37,691 liters) of fuel. The combat radius was 1,175 nautical miles (1,352 statute miles/2,176 kilometers) with a 10,000 pound (4,536 kilogram) bomb load.

Planned armament (though the XB-47s were delivered without it) consisted of two .50-caliber machine guns in a tail turret, with 1,200 rounds of ammunition, and 10,000 pounds (4,536 kilograms) of bombs.

Boeing XB-47 Stratojet 46-065, the first of two prototypes, on the ramp at Boeing Field, Seattle, 1 December 1947. (U.S. Air Force)
Boeing XB-47 Stratojet 46-065, the first of two prototypes, on the ramp at Boeing Field, Seattle, 1 December 1947. (U.S. Air Force)

The Stratojet was one of the most influential aircraft designs of all time and its legacy can be seen in almost every jet airliner built since the 1950s: the swept wing with engines suspended on pylons, mounted forward of the leading edge.

2,032 B-47s were built by Boeing Wichita, Douglas Tulsa and Lockheed Marietta. They served the United States Air Force from 1951 to 1977.

Right rear quarter view of Boeing XB-47 Stratojet 46-065. (U.S. Air Force)
Right rear quarter view of Boeing XB-47 Stratojet 46-065. (U.S. Air Force)

The very last B-47 flight took place 18 June 1986 when B-47E-25-DT, serial number 52-166, was flown from the Naval Air Weapons Center China Lake to Castle Air Force Base to be placed on static display.

Boeing XB-47 Stratojet 46-065. (U.S. Air Force)
Boeing XB-47 Stratojet 46-065. (U.S. Air Force 061024-F-1234S-003)

XB-47 45-065 stalled while landing at Larson Air Force Base, near Moses Lake, Washington, 18 August 1951. The crew of three escaped uninjured. The airplane suffered major structural damage. It was returned to Boeing at Seattle, Washington in 1953. The second prototype, XB-47 46-066, is in the collection of the Air Force Flight Test Museum, Edwards Air Force Base, California.

Boeing XB-47 Stratojet 46-066, Sandia. (SDASM)

© 2017, Bryan R. Swopes

17 December 1903, 10:35 a.m.

Aviation, , , , , , , , ,
Orville Wright at the controls of the Flyer, just airborne on its first flight at Kill Devil Hills, North Carolina, 17 December 1903. Wilbur Wright is running along to stabilize the wing. This photograph was taken by John Thomas Daniels, Jr., using the Wright Brothers’ Gundlach Optical Company Korona-V camera. (Library of Congress Prints and Photographs Division)

17 December 1903, 10:35 a.m.: Orville and Wilbur Wright, two brothers from Dayton, Ohio, had been working on the development of a machine capable of flight since 1899. They started with kites and gliders before moving on to powered aircraft. At the Kill Devil Hills near Kitty Hawk, North Carolina, on the eastern shoreline of the United States, they made the first successful flight of a manned, powered, controllable airplane.

Orville was at the controls of the Flyer while Wilbur ran along side, steadying the right wing. Against a 27 miles per hour (12 meters per second) headwind, the airplane flew 120 feet (36.6 meters) in 12 seconds.

Three more flights were made that day, with the brothers alternating as pilot. Wilbur made the last flight, covering 852 feet (263.7 meters) in 59 seconds. The Flyer was slightly damaged on landing but before it could be repaired for an intended flight four miles back to Kitty Hawk, a gust of wind overturned the airplane and caused more extensive damage. It never flew again.

Flyer after fourth (final) flight. (Wright Brothers Aeroplane Company)

The 1903 Wright Flyer is a canard biplane, with elevators to the front and rudders at the rear. The flight controls twisted, or “warped,” the wings to cause a change in direction. The pilot lay prone in the middle of the lower wing, on a sliding “cradle.” He slid left and right to shift the center of gravity. Wires attached to the cradle acted to warp the wings and move the rudders. The airplane is built of spruce and ash and covered with unbleached muslin fabric.

Wright Flyer, front view. (Wright Brothers Aeroplane Company)
Wright Flyer, front view. (Wright Brothers Aeroplane Company)

The Flyer is 21 feet, 1 inch (6.426 meters) long with a wingspan of 40 feet, 4 inches (12.293 meters) and overall height of 9 feet, 3 inches (2.819 meters). The wings have an angle of incidence of 3° 25′. A built-in curvature of the wings creates a continuously-varying anhedral. (The wingtips are 10 inches (25.4 centimeters) lower than at the centerline.) The vertical gap between the upper and lower wings is 6 feet, 2 inches (1.880 meters). There is no sweep or stagger. The total wing area is 510 square feet (47.38 square meters). The Flyer weighs 605 pounds (274.4 kilograms), empty.

Wright Flyer, right quarter view. The airplane was damaged during the landing after its fourth flight. (Wright Brothers Aeroplane Company)

The Flyer was powered by a single water-cooled, normally-aspirated, 201.06-cubic-inch-displacement (3.30 liter) 4-cylinder inline overhead valve gasoline engine, which produced 12 horsepower at 1,025 r.p.m. The engine was built by the Wright’s mechanic, Charlie Taylor. The engine has a cast aluminum alloy crankcase with cast iron cylinders. Fuel is supplied from a gravity-feed tank mounted under the leading edge of the upper wing. Total fuel capacity is 22 fluid ounces (0.65 liters).

Wright Flyer, left profile. (Wright Brothers Aeroplane Company)
Wright Flyer, right profile. (Wright Brothers Aeroplane Company)

Using chains, sprockets, and drive shafts, the engine turns two fixed-pitch wooden propellers in opposite directions at 350 r.p.m. They turn outboard at the top of their arcs. The propellers have a diameter of 8 feet, 6 inches (2.591 meters) and are positioned at the trailing edges of the wings in a pusher configuration.

The Wright's airfield at Kittyhawk, North Carolina. Wilbure Wright is standing in the hangar. (Wright Brothers Aeroplane Company)
The Wright’s airfield near Kittyhawk, North Carolina. Wilbur Wright is standing in the hangar. (Wright Brothers Aeroplane Company)

In 1928, the Wright Flyer was shipped to England where it was displayed at the Science Museum on Exhibition Road, London. It returned to the United States in 1948 and was placed in the collection of the Smithsonian Institution.

The Wright Brothers’ first airplane flew a total of 1 minute, 42.5 seconds, and travelled 1,472 feet (448.7 meters).

The 1903 Wright Flyer at the Smithsonian Institution. (Photo by Eric Long, National Air and Space Museum, Smithsonian Institution)
The 1903 Wright Flyer at the Smithsonian Institution. (Photo by Eric Long, National Air and Space Museum, Smithsonian Institution)

Wilbur Wright died of typhoid fever in 1912. Orville continued to fly until 1918. He served as a member of the National Advisory Committee on Aeronautics (NACA, predecessor of NASA) for 28 years. He died in 1948.

The Boeing XB-15, 35-277, flies past the Wright Brothers Memorial at the Kill Devil Hills, near Kitty Hawk, North Carolina. (U.S. Air Force)

© 2018, Bryan R. Swopes