Tag Archives: First Flight

15 May 1941

May 15, 2025AviationFirst Flight, Flying Officer Phillip Edward Gerald Sayer OBE, Frank Whittle, Gerry Sayer, Gloster-Whittle E.28/39, Officer of the Most Excellent Order of the British Empire, Power Jets (Research and Development Ltd., RAE Farnborough, RAF Cranwell, W4041/G, Whittle Supercharger Type W.1Bryan Swopes

Gloster-Whittle E.28/39 W4041/G in its original configuration. The horizontal paint stripe was used as an indication of heating by the turbojet engine. (BAE Systems)

15 May 1941: Having been delayed by weather until 7:40 p.m., Gloster Aircraft Co., Ltd., Chief Test Pilot Phillip Edward Gerald Sayer taxied into position on the long, hard-surfaced runway at RAF Cranwell, stood on the brakes and advanced the throttle. When the engine reached 16,000 r.p.m., Sayer released the brakes and the little airplane began to roll forward.

Acceleration was slow. Relying on the feel of the flight controls rather than a pre-calculated airspeed, Sayer lifted off after 600–700 yards (550–640 meters), at about 80 miles per hour (129 kilometers per hour). At 1,000 feet (305 meters), he retracted the landing gear and continued to climb at reduced r.p.m. He reached a maximum 240 miles per hour (386 kilometers per hour) Indicated Air Speed at 4,000 feet (1,219 meters).

Sayer landed after a 17-minute first flight.

Gerry Sayer's knee board notations from the Gloster E.28/39 first flight, 15 May 1941. (Hartley Moyes, courtesy of Neil Corbett, Test and Research Pilots, Flight Test Engineers) — Gerry Sayer’s knee board notations from the Gloster E.28/39 first flight, 15 May 1941. (Hartley Moyes, courtesy of Neil Corbett, Test and Research Pilots, Flight Test Engineers)

The airplane was the Gloster-Whittle E.28/39, registration W4041/G, the first of two prototype fighters powered by a turbojet engine. (The “/G” in the registration indicates that, for security reasons, the airplane is at all times to be under guard when on the ground.) It was a single-seat, single-engine, low-wing monoplane of all-metal construction. The E.28/39 had retractable tricycle landing gear, one of the first fighter-type aircraft with that configuration.

The Gloster E.28/39 was 25 feet, 3 inches (6.696 meters) long with a wingspan of 29 feet, 0 inches (8.839 meters) and overall height of 9 feet, 3 inches (2.819 meters). It had a fuel tank of just 81 gallons (368 liters) capacity. The prototype’s takeoff weight was 3,341 pounds (1,515 kilograms).

Power Jets, Ltd. Whittle Supercharger Type 1 turbojet engine, as seen from the front. (Science Museum Group) — Power Jets, Ltd., Whittle Supercharger Type W.1 turbojet engine, as seen from the front. Air enters the compressor through barely visible intakes in the sides of the cast aluminum alloy compressor case. (Science Museum Group)

Whittle W.1 combustion chambers and exhaust as seen from the rear. The turbine section was water-cooled. (Getty Images/Science & Society Picture Library)

W4041/G was powered by a single Power Jets, Ltd., Whittle Supercharger Type W.1. The turbojet used a single-stage, centrifugal-flow compressor, ten reverse-flow combustion chambers, and a single-stage axial-flow turbine. The turbine had 72 blades. The W.1 produced 860 pounds of thrust (3,825.47 Newtons) at 16,500 r.p.m., burning paraffin (kerosene).

Gloster-Whittle E.28/39 W4041/G, front. (Gloster)

The E.28/39 had a single large air intake at the nose. This split into two ducts which passed around each side of the the cockpit, following the inner contours of the fuselage, and then entered a plenum chamber. Intake air was compressed approximately 4:1 and passed to the combustion chambers. Fuel was mixed with this heated, compressed air, then ignited. Flame temperatures approached 600 °C. (1,112 °F.) This very hot, expanding gas flowed through spiral ducts to the turbine blades, causing the turbine disc to spin to a maximum 17,750 r.p.m., above 4,000 feet (1,219 meters).

Diagram of fuselage arrangement of E.28/39. (Air Cdre Sir Frank Whittle)

The turbine drove the compressor at the front of the engine through a central drive shaft. The exhaust gas left the engine and passed through a straight pipe to the rear of the fuselage. The high velocity gas exiting the tail of the aircraft—thrust—resulted in the aircraft being propelled forward at a proportional velocity.

Gloster-Whittle E.28/39 W4041/G, rear (Gloster)

Because of limitations in materials technology, the Whittle W.1 had a limited service life of just ten hours. To keep the most time available for flight tests, early static and taxi tests of the Gloster prototype were made using an engine built from non-airworthy parts and spare components. This engine was designated W.1X.

Over the next thirteen days, Gerry Sayer made fourteen flights, totaling ten hours. The E.28/39 reached a maximum of 25,000 feet (7,620 meters) and 300 miles per hour (483 kilometers per hour). W4041/G was restricted to 2g maneuvers because of stress placed on the cast aluminum compressor case.

Gloster test pilots conducted three series of flight tests with W.4041/G. With Gloster test pilot John Grierson in the cockpit, on 24 June 1943, W4041/G climbed to 41,600 feet (12,680 meters) in 27 minutes, and reached an absolute maximum altitude of 42,170 feet (12,853 meters). This flight completed Gloster’s flight test program and the airplane was turned over to RAE Farnborough.

A second Gloster E.28/39 was built, W4046/G. Using an improved Whittle W.2/700 turbojet engine, the second prototype reached a maximum speed of 505 miles per hour (813 kilometers per hour) in level flight at 30,000 feet (9,144 meters)—0.74 Mach.

On 30 July 1943, W4046 was lost when its ailerons jammed at high altitude. The pilot bailed out and parachuted safely, but the prototype jet airplane was destroyed.

Wreckage of W4046/G — Wreckage of the second prototype Gloster E.28/39, W4046/G

On 27 April 1946, Gloster-Whittle E.28/39 W4041/G was placed in the National Aeronautical Collection, Science Museum, South Kensington, 27 April 1946.

Chief Test Pilot Phillip Edward Gerald Sayer, Esq., was appointed an Officer of the Most Excellent Order of the British Empire (OBE) on the New Years Honours list, 30 December 1941. He was killed in flying accident 22 October 1942, probably the result of a mid-air collision.

RECOMMENDED: “No Airscrew Necessary. . .” by Robert J. Blackburn, Flight and Aircraft Engineer, No. 2131, Vol. LVI., Thursday, 27 October 1949, at pages 553–558

Gloster-Whittle E.28/39, W4041/G, piloted by Squadron Leader J. Moloney, takes off from RAE Farnborough for a test flight. (Flight Lieutenant Stanley Devon, Royal Air Force Official Photographer. © Imperial War Museum CH 14832A) — Gloster-Whittle E.28/39, W4041/G, now in standard camouflage and RAF markings, piloted by Squadron Leader J. Moloney, takes off from RAE Farnborough for a test flight. Note the small outboard vertical fins on the horizontal stabilizer. (Flight Lieutenant Stanley Devon, Royal Air Force Official Photographer. © Imperial War Museum CH 14832A)

13 May 1949

May 13, 2025AviationA13/A617963, A14/A617964, B3/45 Prototype, Bee Beamont, Canberra B Mk.1, English Electric A.1, English Electric Co. Ltd., First Flight, Martin B-57 Canberra, Prototype, Roland Prosper Beamont, Rolls-Royce Avon R.A.2, Test Pilot, VN799, Warton AerodromeBryan Swopes

English Electric A.1 VH799, first of four prototypes of the Canberra bomber. (BAE Systems)

Bee Beamont with an English Electric Canberra

Friday, 13 May 1949: At Warton Aerodrome, Lancashire, Chief Test Pilot Roland Prosper Beamont, C.B.E., D..S.O and Bar, D.F.C. and Bar, made the first test flight of the English Electric A.1 prototype, VN799, a very high altitude light bomber powered by two turbojet engines.

VN799 was the first of four prototypes. Three were equipped with Rolls-Royce engines.

The newly completed airplane had been rolled out 2 May, and over the next several days underwent a series of static and taxi tests. The prototype was painted overall “plate blue.”

Rollout of English Electric A.1 VN799 at Warton Aerodrome, 2 May 1949.

Airworthiness certificate — Ministry of Aircraft Production authorization for the Canberra’s first flight. The test pilot is specified by name. The serial numbers of the two Rolls-Royce jet engines are also listed.

“Bee” Beamont flew the prototype for approximately one-half hour. Other than a problem in yaw, which would be corrected with minor modifications to the vertical fin and rudder over the next several test flights, the aircraft performed very well. Months earlier, the bomber had been ordered into production “off the drawing board.”

English Electric A.1 VN799. Note the rounded vertical fin of this early configuration.

British bombers have traditionally been named for cities. Canberra, capitol of Australia, was selected as the new airplane’s name in January 1950.

The English Electric B. Mk. I was a twin engine mid-wing bomber, operated by a pilot and navigator/bombardier. The Mk. I was 63 feet, 11 inches (19.482 meters) long, with a wing span of 66 feet, 3 inches (20.193 meters), and overall height of 15 feet, 6.9 inches. (4.747 meters). The wing used a symmetrical airfoil and had 2° angle of incidence. The inner wing had 2° dihedral, and the outer wing, 4° 21′. The total wing area was 960 square feet (89.2 square meters). The tailplane had a span of 27 feet, 4.9 inches (8.354 meters) with 1° angle of incidence and 10° dihedral. Total area of the stabilizer and elevators was 171.1 square feet (15.90 square meters).

Canberra VN799 at Farnborough Air Show, 1949. Note the squared-off vertical fin. (Ed Coates Collection)

VN799 was powered by two pre-production Rolls-Royce Avon R.A.2 engines. The Avon R.A.2 was a single-spool, axial flow turbojet with a 12-stage compressor section and single-stage turbine. It was rated at 6,000 pounds of thrust (26.69 kilonewtons). It weighed 2,400 pounds (1,089 kilograms). VN799 was the first British airplane built with an axial-flow turbojet engine.

VN799, flown by Flight Lieutenant Harry Maule with Scientific Officer I Mike Burgan, crashed at Sutton Heath, near RAF Woodbridge, 18 August 1953. The engines stopped due to fuel exhaustion while testing automatic landing systems. Maule and Burgan suffered minor injuries, but the airplane was destroyed. At the time of the crash, the prototype Canberra had flown a total of 1,540 hours, 40 minutes.

This Canberra T.4 WJ874 is painted as the first prototype B.1, VH799.(Ministry of Defense) — Canberra T.4 WJ874 is painted as the first prototype, VN799. (Ministry of Defense)

Interestingly, in October 1946, a 34-passenger civil transport variant of the Canberra was proposed, with an enlarged 10-foot-diameter fuselage.

The Canberra was produced in bomber, intruder, photo reconnaissance, electronic countermeasures and trainer variants by English Electric, Handley Page, A.V. Roe and Short and Harland. In the United States, a licensed version, the B-57A Canberra, was built by the Glenn L. Martin Company. The various versions were operated by nearly 20 nations. The Canberra was the United Kingdom’s only jet-powered bomber for four years. The last one in RAF service, a Canberra PR.9, made its final flight on 28 July 2008.

Colonel Charles E. ("Chuck") Yeager, USAF, commanding the 405th Fighter Wing, with crew chief TSGT Rodney Sirois, before a combat mission with a Martin B-57 Canberra during the Vietnam War. (Andrew Headland, Jr./Stars and Stripes) — Colonel Charles E. (“Chuck”) Yeager, USAF, commanding the 405th Fighter Wing, with crew chief TSGT Rodney Sirois, before a combat mission with a Martin B-57 Canberra bomber during the Vietnam War. (Andrew Headland, Jr./Stars and Stripes)

10 May 1972

May 10, 2025Aviation71-1369, 75-0294, Cl, Fairchild Republic YA-10A Thunderbolt II, First Flight, General Electric GAU-8 Avenger, Howard Verner Nelson, PrototypeBryan Swopes

Fairchild Republic YA-10A 71-1369. (U.S. Air Force)

10 May 1972: Chief test pilot Howard W. (“Sam”) Nelson made the first flight of the prototype Fairchild Republic YA-10A Thunderbolt II, 71-1369, at Edwards Air Force Base in the high desert of southern California.

the first prototype Fairchild Republic YA-10A, 71-1369, landing at Edwards Air Force Base. (U.S. Air Force)

The production A-10A Thunderbolt II is a single-place, twin engine low-wing monoplane with retractable tricycle landing gear. The airplane is 52 feet, 7 inches (16.027 meters) long with a wing span of 57 feet, 6 inches (17.526 meters), and overall height of 14 feet, 8 inches (4.470 meters). Its operating weight is 24,513 pounds (11,119 kilograms) and the maximum takeoff weight is 50,000 pounds (22,680 kilograms). This includes the operating weight plus full internal fuel, 1,350 rounds of ammunition and 18 Mk.82 bombs.

The A-10 is powered by two General Electric TF34–GE-100 engines. These are two-spool axial flow turbofans with a single stage fan section, 14-stage compressor, and 6-stage turbine. The engines produce a maximum 8,900 pounds of thrust ( kilonewtons).

A General Electric GAU-8/A Avenger autocannnon installed in a Fairchild A-10 Thunderbolt II. (U.S. Air Force)

The A-10 was designed and built around its hydraulically-operated General Electric GAU-8 Avenger 30 mm Gatling-type autocannon. The gun has 7 rotating barrels and is capable of firing at a rate of 4,300 rounds per minute. The Thunderbolt II can carry a maximum of 1,350 rounds of high explosive-incendiary or armor piercing-incendiary ammunition.

Howard Verner Nelson was born on New Year’s Eve, 31 December 1924, at Hartford Connecticut. He was the second son of Gustaf B. Nelson, a clerk, and Signe Ottilia Nelson.

Nelson entered the United States Army Air Forces on 20 November 1944, and remained on active duty in the U.S. Air Force until 28 May 1957, when he transferred to the Air Force Reserve. He rose to the rank of lieutenant colonel. He flew 105 combat missions during the Korean War.

“Sam” Nelson joined the Republic Aviation Corporation in 1960. He was assigned Republic’s chief test pilot for the F-105 Thunderchief supersonic fighter bomber. In October 1976, Nelson was promoted to Director of Flight Operations.

Nelson was killed at the Paris Air Show 3 June 1977 while demonstrating an A-10A Thunderbolt II.

Lieutenant Colonel Nelson’s remains were buried at the Arlington National Cemetery.

Fairchild Republic A-10A Thunderbolt II 75-0294 crashed on the runway at the Paris Air Show, 3 June 1977. Director of Flight Operations Howard W. Nelson died enroute to a hospital. (Unattributed)

6 May 1941

May 6, 2025Aviation40-3051, Alexander Kartveli, Alexander Kartvelishvili, Browning Machine Gun Caliber .50 AN-M2, Curtiss Electric Propellers, Fighter, Fighter Bomber, First Flight, Lowery Lawson Brabham, Pratt & Whitney Double Wasp TSB1-G, Pratt & Whitney XR-2800-21, Prototype, Republic Aviation Corporation, Republic XB-47B Thunderbolt, Test Pilot, World War II, ალექსანდრე ქართველიშვილიBryan Swopes

Republic XP-47B 40-3051 prototype in flight. (Republic Aircraft Corporation)

6 May 1941: Just eight months after a prototype for a new single-engine fighter was ordered by the U.S. Army Air Forces, test pilot Lowery Lawson Brabham took off from the Republic Aviation Corporation factory airfield at Farmingdale, New York, and flew the prototype XP-47B Thunderbolt, serial number 40-3051, to Mitchel Field, New York.

During the flight, oil which had collected in the exhaust duct began burning. There was so much smoke that Brabham considered bailing out. He stayed with the prototype, though, and when he arrived at Mitchel Field, he exclaimed, “I think we’ve hit the jackpot!”

Kartveli, Alexander — Alexander Kartveli

The prototype was designed by Alexander Kartveli, a Georgian immigrant and former chief engineer for the Seversky Aircraft Corporation, which became the Republic Aviation Corporation in 1939.

Alexander Kartveli (née Kartvelishvili, ალექსანდრე ქართველი) was born in Tbilisi, in the Kutais Governorate of the Russian Empire, (what is now, Georgia). After World War I, during which he was wounded, Kartvelishvili was sent to study at the Paris Aviation Higher College of Engineering in France by the government of the Democratic Republic of Georgia. He graduated in 1922. Kartvelishvili did not return to his country, which had fallen to the Red Army in the Soviet-Georgian War. He worked for Blériot Aéronautique S.A. until 1928, when he was employed by the Fokker American Company (also known as Atlantic Aircraft, or Atlantic-Fokker) which was headquartered at Passaic, New Jersey, in the United States. In 1931, he became chief engineer for the Seversky Aircraft Company in Farmingdale.

Republic XP-47B Thunderbolt prototype 40-3051 at Farmingdale, New York, 1941. The pilot standing in front of the airplane gives a scale reference. (Republic Aviation Corporation)

Kartveli submitted his design proposal for the XP-47B to the U.S. Army Air Corps, 12 June 1940. The prototype was ordered 6 September, and a week later, 13 September 161 production P47Bs and 602 P-47Cs were ordered. The contract was for $56,499,924. The company named the new fighter “Thunderbolt,” which had been suggested by C. Hart Miller, director of the military contracts division of Republic Aviation.

The XP-47B was the largest single-engine fighter that had yet been built. The production P-47B was 34 feet, 10 inches (10.617 meters) long with a wingspan of 40 feet, 9-5/16 inches (12.429 meters), and height of 12 feet, 8 inches (3.861 meters).¹ The wing area was 300 square feet (27.9 square meters). At a gross weight of 12,086 pounds (5,482 kilograms), it was nearly twice as heavy as any of its contemporaries.

Republic XP-47B Thunderbolt 40-3051 at Wright Field, Dayton, Ohio.(Ray Wagner Collection, San Diego Air & Space Museum Archives )

The XP-47B was powered by an air-cooled, supercharged and turbocharged, 2,804.4-cubic-inch-displacement (45.956 liter) Pratt & Whitney R-2800-21 (Double Wasp TSB1-G) two-row, 18-cylinder radial with a compression ratio of 6.65:1 had a normal power rating of 1,625 horsepower at 2,550 r.p.m., to an altitude of 25,000 feet (7,620 meters), and a takeoff/military power rating of 2,000 horsepower at 2,700 r.p.m. at 25,000 feet (7,620 meters). The engine drove a 12-foot, 2 inch (3.708 meter) diameter, four-bladed Curtiss Electric constant-speed propeller through a 2:1 gear reduction. The R-2800-21 was 4 feet, 4.50 inches (1.340 meters) in diameter and 6 feet, 3.72 inches (1.923 meters) long. The engine weighed 2,265 pounds (1,027 kilograms). Approximately 80% of these engines were produced by the Ford Motor Company. It was also used as a commercial aircraft engine, with optional propeller gear reduction ratios.

A large General Electric turbosupercharger was mounted in the rear of the fuselage. Internal ducts carried exhaust gases from the engine to drive the turbocharger. This supercharged air was then carried forward through an intercooler and then on to the carburetor to supply the engine. The engine’s mechanical supercharger further pressurized the air-fuel charge.

Republic XP-47B 40-3051. The pilot enters the cockpit through a hinged canopy segment. (Ray Wagner Collection Catalog, San Diego Air and Space Museum)

During flight testing, the XP-47B Thunderbolt demonstrated speeds of 344.5 miles per hour (554.4 kilometers per hour) at 5,425 feet (1,654 meters), and 382 miles per hour (615 kilometers per hour) at 15,600 feet (4,745 meters). Its maximum speed was 412 miles per hour (663 kilometers per hour) at 25,800 feet (7,864 meters). The test pilot reported that the engine was unable to produce full power during these tests. It was determined that it had a cracked cylinder head, resulting in a loss of 2.5–4% of its maximum rated power. Also, the XP-47B was painted in camouflage, resulting in a slight loss of speed.

It could climb to 15,000 feet (4,572 meters) in just five minutes.

The Thunderbolt was armed with eight Browning AN-M2 .50-caliber machine guns, four in each wing, with 3,400 rounds of ammunition. It could also carry external fuel tanks, rockets and bombs. The structure of the P-47 could be described as “robust” and it was heavily armored. The amount of damage that the airplane could absorb and still return was remarkable.

Republic XP-47B Thunderbolt 40-3051, 4 May 1941. (U.S. Air Force) — Republic XP-47B Thunderbolt 40-3051, 4 May 1941. (Republic Aviation Corporation)

During a test flight, 4 August 1942, the XP-47B’s tail wheel was left down. The extreme heat of the turbocharger’s exhaust set fire to the tire, which then spread to the airplane’s fabric-covered control surfaces. Unable to control the airplane, test pilot Filmore L. Gilmer bailed out. The prototype Thunderbolt crashed into Long Island Sound and was destroyed.

The third production Republic P-47B Thunderbolt, 41-5897, at Langley Field, Virginia, 24 March 1942. The door-hinged canopy of the XP-47B has been replaced by a rearward-sliding canopy, requiring that the radio antenna mast be moved.(NASA)

A Republic P-47B Thunderbolt in the NACA Full Scale Tunnel, 31 July 1942. (NASA LMAL 29051)

A total of 15,683 Thunderbolts were built; more than any other U.S. fighter type. In aerial combat, it had a kill-to-loss ratio of 4.6:1. The P-47, though, really made its name as a ground attack fighter, destroying aircraft, locomotives, rail cars, and tanks by the many thousands. It was one of the most successful aircraft of World War II.

¹ Data from Pilot’s Flight Operating Instructions, Technical Order No. 01-65BC-1, 20 January 1943

6 May 1935

May 6, 2025AviationBenjamin Scovill Kelsey, Curtiss Electric Propellers, Curtiss-Wright Airplane Division, Curtiss-Wright Corporation, Curtiss-Wright Model 75, Donovan Reese Berlin, Fighter, First Flight, NX17Y, s/n 11923, Wright Aeronautical Division, Wright GR1670A1Bryan Swopes

Curtiss-Wright Model 75, X17Y. (Ray Wagner Collection, San Diego Air & Space Museum Archives)

6 May 1935: At Buffalo, New York, the prototype Curtiss-Wright Model 75, X17Y, serial number 11923, made its first flight.

Donovan Reese Berlin. (Niagara Aerospace Museum)

Designed by Donovan Reese Berlin, the airplane was a modern design of all metal construction, with fabric covered control surfaces. The Model 75 was a single-seat, single-engine low-wing monoplane with retractable landing gear.

In its original configuration, the Model 75 was powered by an air-cooled, supercharged 1,666.860 cubic inch displacement (27.315 liter) Wright Aeronautical Division GR1670A1 two-row 14-cylinder radial engine. The GR1670A1 was a developmental engine with a compression ratio of 6.75:1. It was rated at 775 horsepower at 2,400 r.p.m. at Sea Level, and 830 horsepower at 2,600 r.p.m. for takeoff, burning 87-octane gasoline. The engine was 3 feet, 9 inches (1.143 meters) in diameter, 4 feet, 4–25/32 inches (1.341 meters) long, and weighed 1,160 pounds (526 kilograms). The GR1670A1 drove a three-bladed Curtiss Electric constant-speed propeller through a 16:11 gear reduction.

The GR1670A1 was also used in the Seversky SEV-S1, NR18Y, a record-setting experimental variant of the rival Seversky P-35.

The United States Department of Commerce, Bureau of Air Commerce, registered X17Y to the Curtiss-Wright Corporation, Kenmore & Vulcan Street, Buffalo, New York, on issued 1 June 1936. This registration was cancelled 26 April 1937.

The Curtiss-Wright Model 75 would be developed into the P-36 Hawk fighter for the U.S. Army Air Corps. France ordered it as the H75A-1, and in British service, it was known as the Mohawk Mk.I.

The tenth production P-36 was modified with a liquid-cooled Allison V-1710 V-12 engine to become the prototype XP-40.