Tag Archives: Pan American World Airways

20 December 1957

Boeing 707-121 N708PA, photographed during its second flight. (Boeing via Space.com)
Boeing 707-121 N708PA, photographed during its second flight on the afternoon of 20 December 1957. (Boeing)
Boeing 707-121 N708PA makes its first takeoff at 12:30 p.m., on a rainy afternoon, 20 December 1957. (Unattributed)
Boeing 707-121 N708PA makes its first takeoff at 12:30 p.m. on a rainy afternoon, 20 December 1957. (Boeing)

20 December 1957: The first production Boeing 707 jet-powered commercial airliner, N708PA, made its first flight at Renton, Washington. Alvin M. “Tex” Johnston, Boeing’s Chief of Flight Test, was in command, with co-pilot James R. Gannet and flight engineer Tom Layne. Takeoff was at 12:30 p.m., PST. Poor weather limited the first flight to just 7 minutes. The new airliner landed at Boeing Field. Later that day, a second flight was made, this time with a duration of 1 hour, 11 minutes.

N708PA (Serial Number 17586, Line Number 1) was a Model 707-121. The new airliner had been sold to Pan American World Airways, the launch customer, as part of an order for twenty 707s in October 1955.

Boeing test pilot Alvin M. "Tex" Johnston in the cockpit of of the 367–80. (LIFE)
Boeing’s Chief of Flight Test, Alvin M. “Tex” Johnston, in the cockpit of of the 367–80, “Dash Eighty,” 1954. (LIFE Magazine via Jet Pilot Overseas)

The Boeing Model 707 was developed from the earlier Model 367–80, the “Dash Eighty,” prototype for an air-refueling tanker which would become the KC-135A Stratotanker. The 707 was a four-engine jet transport with swept wings and tail surfaces. The leading edge of the wings were swept at a 35° angle.

N708PA was initially used for flight testing by Boeing. Once this was completed, it was prepared for commercial service and delivered to Pan American at San Francisco International Airport (SFO), 30 November 1958. Pan Am named the new airliner Clipper Constitution.

Boeing 707-121 708PA under maintenance at Renton, Washington. (Boeing)
Boeing 707-121 N708PA under maintenance at Renton, Washington. (Boeing)

In February 1965, the airliner was upgraded to 707-121B standards, which replaced the original turbojet engines with quieter, more efficient Pratt & Whitney JT3D-1 turbofan engines which produced 17,000 pounds of thrust. The wing inboard leading edges were modified to the design of the Model 720 and there was a longer horizontal tail plane.

Clipper Constitution flew for Pan Am for nearly seven years, until 17 September 1965 when it crashed into Chances Peak, a 3,002 foot (915 meters) volcano on the Caribbean island of Montserrat. The point impact  was 242 feet (74 meters) below the summit. All aboard, a crew of 9 and 21 passengers, were killed.

Boeing 707-121 N708PA, with both Boeing and Pan American corporate markings. (Unattributed)
Boeing 707-121 N708PA, with both Boeing and Pan American corporate markings. (Unattributed)

The Boeing Model 707-121 was a four-engine jet transport with swept wings and tail surfaces. The leading edge of the wings were swept at a 35° angle. The airliner had a flight crew of four: pilot, co-pilot, navigator and flight engineer.

The 707-121 was 145 feet, 1 inch (44.221 meters) long with a wing span of 130 feet, 10 inches (39.878 meters). The top of the vertical fin stood 42 feet, 5 inches (12.929 meters) high. The 707 pre-dated the ”wide-body” airliners, having a fuselage width of 12 feet, 4 inches (3.759 meters). The airliner’s empty weight is 122,533 pounds (55,580 kilograms). Maximum take off weight is 257,000 pounds (116,573 kilograms).

The first versions were powered by four Pratt & Whitney Turbo Wasp JT3C-6 turbojet engines, producing 11,200 pounds of thrust (49,820 kilonewtons), and 13,500 pounds (60.051 kilonewtons) with water injection. This engine was a civil variant of the military J57 series. It was a two-spool axial-flow turbojet engine with a 16-stage compressor and 2 stage turbine. The JT3C-6 was 11 feet, 6.6 inches (3.520 meters) long, 3 feet, 2.9 inches (0.988 meters) in diameter, and weighed 4,235 pounds (1,921 kilograms).

At MTOW, the 707 required 11,000 feet (3,352.8 meters) of runway to take off.

The 707-121 had a maximum speed of 540 knots (1,000 kilometers per hour). It’s range was 2,800 nautical miles (5,186 kilometers).

The Boeing 707 was in production from 1958 to 1979. 1,010 were built. Production of 707 airframes continued at Renton until the final one was completed in April 1991. As of 2011, 43 707s were still in service.

Boeing 707-121 N708PA retracts its landing gear after taking off at Seattle Tacoma Airport. (Unattributed)
Boeing 707-121 N708PA retracting its landing gear after takeoff at Seattle Tacoma Airport. (Unattributed)

© 2016, Bryan R. Swopes

10 December 1958

One of the first Boeing 707 airliners delivered to Pan American World Airways, Clipper Maria, N707PA. (Pan Am)
One of the first Boeing 707 airliners delivered to Pan American World Airways, Clipper Maria, N707PA. (Pan Am)

10 December 1958: Using a Boeing 707 leased from Pan American World Airways, National Airlines became the first U.S. airline to operate jet airliners within the United States.

Pan American’s Clipper America, N710PA, a Boeing 707-121, departed Idlewild Airport (IDL), New York City, New York, at 9:54 a.m., Eastern Standard Time, bound for Miami International Airport (MIA), Florida, 949 nautical miles (1,092 statute miles/1,756 kilometers) to the south-southwest. The National Airlines pilots were Captain Roger Whittacker and Captain David B. Gannon. The airliner carried 102 passengers.

N710PA arrived at Miami at 12:39 p.m. Departing Miami at 2:13 p.m., returned to New York and touched down at Idlewild at 4:52 p.m. The 707 was flown on a scheduled Pan Am flight that night.

A contemporary news magazine article discussed the lease arrangement:

National Airlines timetable, 26 October 1958. (Don Henchel Collection via Airline Timetable Images)
National Airlines timetable, 26 October 1958. (Don Henchel Collection via Airline Timetable Images)

“Monday, Dec. 08, 1958: One of the few U.S. airlines climbing out of the labor fog last week was National Airlines, whose routes stretch along the Atlantic Coast to Florida. On Dec. 10 National will inaugurate the first domestic jet airliner service with daily flights on the rich New York-Miami run. Using 600-m.p.h. Boeing 707s under a complicated lease-stock deal with Pan American, which already flies jets across the Atlantic, National will make the 1,100-mile run in 2 hr. 15 min. To make sure that it can fly jets, National signed contracts with its pilots, flight engineers and mechanics running into 1960. National is paying well to be the first domestic jet operator. Plans call for three 707s under lease around the first of the year, each one costing an estimated $216,000 per month to operate and maintain. To sweeten the kitty. National has also agreed to a stock exchange that, if CAB approves, will eventually give Pan Am a big voice in its affairs. In a $16 million swap, the two lines will exchange 400,000 shares of stock, and Pan Am will get a two-year option to buy another 250,000 shares of National stock at $22.50 per share. The effect would be to give National a minor (6%) interest in Pan American, while Pan Am could gain 36% of National if it exercises its option. . . .”

TIME Magazine, 8 December, 1958

American Airlines was the first domestic carrier to fly its own Boeing 707s, with the first flight from Los Angeles to new York, 25 January 1959.

National Airlines was a domestic carrier, founded in 1930. Pan Am acquired the airline 7 January 1980.

Screen Shot 2015-12-11 at 17.26.30
National Airlines advertisement, Fall 1958. (Don Henchel Collection via Airline Timetable Images)

The Boeing 707 was developed from the earlier Model 367–80, the “Dash Eighty.”

The Boeing Model 707-121 was a four-engine jet transport with swept wings and tail surfaces. The leading edge of the wings were swept at a 35° angle. The airliner had a flight crew of four: pilot, co-pilot, navigator and flight engineer.

The 707-121 was 145 feet, 1 inch (44.221 meters) long with a wing span of 130 feet, 10 inches (39.878 meters). The top of the vertical fin stood 42 feet, 5 inches (12.929 meters) high. The 707 pre-dated the ”wide-body” airliners, having a fuselage width of 12 feet, 4 inches (3.759 meters). The airliner’s empty weight is 122,533 pounds (55,580 kilograms). Maximum take off weight is 257,000 pounds (116,573 kilograms).

The first versions were powered by four Pratt & Whitney Turbo Wasp JT3C-6 turbojet engines, producing 11,200 pounds of thrust (49.82 kilonewtons), and 13,500 pounds (60.051 kilonewtons) with water injection. This engine was a civil variant of the military J57 series. It was a two-spool axial-flow turbojet engine with a 16-stage compressor and 2 stage turbine. The JT3C-6 was 11 feet, 6.6 inches (3.520 meters) long, 3 feet, 2.9 inches (0.988 meters) in diameter, and weighed 4,235 pounds (1,921 kilograms).

At MTOW, the 707 required 11,000 feet (3,352.8 meters) of runway to take off.

The 707-121 had a maximum speed of 540 knots (1,000 kilometers per hour). It’s range was 2,800 nautical miles (5,185.6 kilometers).

N710PA, c/n 17589, was delivered to Pan American 29 September 1958. It was later renamed Clipper Caroline. In 1965, the airliner was upgraded to the 701-121B configuration. After being sold by Pan Am, it served with a number of different companies. It was scrapped in 1984.

Note: Thanks to regular TDiA reader Tom Facer for suggesting this post.

© 2018, Bryan R. Swopes

28 October 1957

The first production Boeing 707 after being rolled out of the final assembly plant at Renton, Washington, 28 October 1957. (Boeing)

28 October 1957: The first production Boeing 707 jet-powered commercial airliner, serial number 17586 (Line Number 1), was rolled out at the Boeing aircraft assembly plant at Renton, Washington. The Model 707 was developed from the earlier Model 367–80, the “Dash Eighty,” prototype for an air-refueling tanker which would become the KC-135 Stratotanker.

17586 was a Model 707-121. The new airliner had been sold to Pan American World Airways, the launch customer, as part of an order for twenty 707s in October 1955. The Federal Aviation Agency (FAA) assigned N708PA as its registration mark.

The first production Boeing 707 after roll out, 28 October 1957. (Boeing)

N708PA made its first flight 20 December 1957 with Boeing’s Chief of Flight Test, Alvin M. (“Tex”) Johnston. The airplane was initially used for flight and certification testing. Once this was completed, the new jet airliner was prepared for commercial service and delivered to Pan American at San Francisco International Airport (SFO), 30 November 1958. It was named Clipper Constitution.

Boeing 707-121 N708PA, photographed during its second flight, 20 December 1957. (Boeing)

In February 1965, the airliner was upgraded to 707-121B standards, which replaced the original turbojet engines with quieter, more efficient Pratt & Whitney Turbo Wasp JT3D-1 turbofan engines which produced 17,000 pounds of thrust. The wing inboard leading edges were modified to the design of the Model 720 and there was a longer horizontal tail plane.

Clipper Constitution flew for Pan Am for nearly 8 years, until 17 September 1965, when it crashed into Chances Peak, a 3,002 foot (915 meters) active stratovolcano on the Caribbean island of Montserrat. The point impact was 242 feet (74 meters) below the summit. All aboard, a crew of 9 and 21 passengers, were killed.

Boeing 707-121 N708PA retracts its landing gear after taking off at Seattle Tacoma Airport. (Unattributed)

The Boeing Model 707-121 was a four-engine jet transport with swept wings and tail surfaces. The leading edge of the wings were swept at a 35° angle. The airliner had a flight crew of four: pilot, co-pilot, navigator and flight engineer.

The 707-121 was 145 feet, 1 inch (44.221 meters) long with a wing span of 130 feet, 10 inches (39.878 meters). The top of the vertical fin stood 42 feet, 5 inches (12.929 meters) high. The 707 pre-dated the ”wide-body” airliners, having a fuselage width of 12 feet, 4 inches (3.759 meters).

The first versions were powered by four Pratt & Whitney Turbo Wasp JT3C-6 turbojet engines, producing 11,200 pounds of thrust (49,820 kilonewtons), and 13,500 pounds (60.051 kilonewtons) with water injection. This engine was a civil variant of the military J57 series. It was a two-spool axial-flow turbojet engine with a 16-stage compressor and 3 stage turbine. The JT3C-6 was 11 feet, 6.6 inches (3.520 meters) long, 3 feet, 2.9 inches (0.988 meters) in diameter, and weighed 4,235 pounds (1,921 kilograms).

The airliner’s empty weight is 122,533 pounds (55,580 kilograms). Maximum take off weight is 257,000 pounds (116,573 kilograms). At MTOW, the 707 required 11,000 feet (3,353 meters) of runway to take off.

The 707-121 had a maximum speed is 540 knots (1,000 kilometers per hour). Its range was 2,800 nautical miles (5,186 kilometers).

The Boeing 707 was in production from 1958 to 1979. 1,010 were built. Production of military variants continued until 1994.

© 2018, Bryan R. Swopes

26 October 1958

Pan American World Airways’ Boeing 707-121, N711PA, Clipper America, at Idlewild Airport, New York, 26 October 1958. (Pan American World Airways)

26 October 1958: Pan American World Airways opened the “Jet Age” with the first commercial flight of an American jet airliner. Pan Am’s Boeing 707-121 Clipper America, N711PA, departed New York Idlewild (IDL) on an 8 hour, 41 minute flight to Paris Le Bourget (LBG), with a fuel stop at Gander, Newfoundland (YQX). (The actual flight time was 7 hours.) The distance was 3,634 miles (5,848 kilometers). Aboard were 111 passengers and 11 crewmembers.

A Pan Am company publication explained the need for the stop at Gander:

The Jet could not be fully loaded with fuel before takeoff because of weight restrictions imposed at Idlewild. Fuel capacity of the jet is 17,398 gallons, allowing a cruising range of 4,400 miles. But with a full pay load of passengers, only 9,731 gallons could be taken aboard in New York.

Pan American Clipper, Vol. XV, No. 11, November 1958, Page 6, Column 5

The Boeing 707 was developed from the earlier Model 367–80, the “Dash Eighty”. It is a four-engine jet transport with swept wings and tail surfaces. The leading edge of the wings are swept at a 35° angle. The airliner had a flight crew of four: pilot, co-pilot, navigator and flight engineer. The 707-121 is 145 feet, 1 inch (44.221 meters) long with a wing span of 130 feet, 10 inches (39.878 meters). The top of the vertical fin stands 42 feet, 5 inches (12.929 meters) high. The 707 pre-dated the ”wide-body” airliners, having a fuselage width of 12 feet, 4 inches (3.759 meters).

The first versions were powered by four Pratt & Whitney Turbo Wasp JT3C-6 turbojet engines, producing 11,200 pounds of thrust (49,820 kilonewtons), and 13,500 pounds (60.051 kilonewtons) with water injection. This engine was a civil variant of the military J57 series. It was a two-spool axial-flow turbojet engine with a 16-stage compressor and 2 stage turbine. The JT3C-6 was 11 feet, 6.6 inches (3.520 meters) long, 3 feet, 2.9 inches (0.988 meters) in diameter, and weighed 4,235 pounds (1,921 kilograms).

The airliner’s empty weight is 122,533 pounds (55,580 kilograms). Maximum take off weight (MTOW) is 257,000 pounds (116,573 kilograms). At MTOW, the 707 required 11,000 feet (3,352.8 meters) of runway to take off. Its maximum speed is 540 knots (1,000 kilometers per hour). It had a range of 2,800 nautical miles (5,185.6 kilometers).

The Boeing 707 was in production from 1958 to 1979. 1,010 were built. As of 2011, 43 707s were still in service.

Boeing delivered N711PA to Pan American on 17 October 1958. The airliner was named Clipper America,  but was later renamed Clipper Mayflower. It was leased to Avianca (Aerovías Nacionales de Colombia S.A.) from 1960 to 1962. In April 1965 the 707 was upgraded to the –121B standard. This included a change from the turbojet engines to quieter, more powerful and efficient Pratt and Whitney JT3D-1 turbofans, producing 17,000 pounds of thrust. The wings were modified to incorporate changes introduced with the Boeing 720, and a longer tailplane installed. Pan Ayer of Panama purchased Clipper Mayflower 21 February 1975. It was later leased to Türk Hava Yolları, the Turkish national airline, and went on to serve with Air Asia Company Limited (an Air America aircraft service unit) and E-Systems. After 26 years of service, in August 1984 Clipper America was scrapped at Taipei.

Pan American World Airways’ Boeing 707-121, N711PA, Clipper America, arriving at Aéroport de Paris – Le Bourget, Paris, France, 27 October 1958. (Photograph © Jon Proctor. Used with permission.)

© 2018, Bryan R. Swopes

20 October 1922

1st Lieutenant Harold Ross Harris, Air Service United States Army. (San Diego Air and Space Museum Archives)

20 October 1922: 1st Lieutenant Harold Ross Harris, Air Service, United States Army, the Chief, Flight Test Branch, Engineering Division, at McCook Field, Dayton, Ohio, was test flying a Loening Aeronautical Engineering Company PW-2A monoplane, a single-engine, single-seat fighter. The PW-2A, serial number A.S. 64388, had experimental balance-type ailerons. During this flight, Lieutenant Harris engaged in simulated air combat with Lieutenant Muir Fairchild (future Vice Chief of Staff, United States Air Force) who was flying a Thomas-Morse MB-3.

While banking the PW-2A into a right turn, Harris’ control stick began to vibrate violently from side to side and the airplane’s wings were “torn apart.” With the Loening diving uncontrollably, Harris jumped from the cockpit at approximately 2,500 feet (762 meters). After free-falling about 2,000 feet (610 meters), he pulled the lanyard on his parachute which immediately deployed. Harris then descended with his parachute providing aerodynamic deceleration, coming safely to earth in the back yard of a home at 335 Troy Street. He suffered minor bruises when he landed on a trellis in the garden.

Loening Aeronautical Engineering Company PW-2A, A.S. 64388. This is the airplane from which Lieutenant Harold R. Harris “bailed out” over Dayton, Ohio, 20 October 1922. (San Diego Air and Space Museum)

Harris’ PW-2A crashed into a yard at 403 Valley Street, three blocks away. It was completely destroyed.

This was the very first time a free-fall parachute had been used in an actual inflight emergency. Lieutenant Harris became the first member of the Irvin Air Chute Company’s “Caterpillar Club.”

Crash scene at 403 Valley Street, Dayton, Ohio, 20 October 1922. (U.S. Air Force)

The Pittsburgh Post reported:

Flyer Quits Plane in Parachute, Saves Life; Unique Case

     Dayton, O., Oct. 20.—Leaping from his Loenig [sic] monoplace in a parachute when the plane became uncontrollable over North Dayton today, Lieutenant Harold R. Harris, chief of the flying section of McCook Field, escaped death when his plane crashed to earth.

     Technical data, officials at McCook Field said, show that Lieutenant Harris’ escape is the first time an air pilot has ever actually saved himself by use of a parachute. A mail plane flyer leaped in a parachute over Chicago several years ago, but the necessity of his leaving the plane was questioned.

     Harris won the commercial plane event in the Pulitzer races in Detroit last week, flying the “Honeymoon Express” plane.

The Pittsburgh Post, Saturday, 21 October 1922, Vol. 80, No. 303, Page 1, Column 1

Harold R. Harris was born at Chicago, Illinois, 20 December 1895, the first of four children of Ross Allen Harris, M.D., and Mae Ermine Plumb Harris. He enlisted as a private in the Aviation Section, Signal Enlisted Reserve Corps (E.R.C.), 2 May 1917. He was commissioned as a 2nd Lieutenant, Aviation Section, Signal Officers Reserve Corps (O.R.C.) on 15 December 1917. Harris was promoted to the rank of 1st Lieutenant on 19 January 1918. His commission was vacated 18 September 1920 and commissioned as a 1st Lieutenant, Air Service, United States Army, effective 1 July 1920.

Married Grace C. Harris, circa 1920. They had two children.

Ross attended the Air Service Engineering School, graduating in 1922. He also earned a Bachelor of Science degree (B.S.) from the California Institute of Technology, Pasadena, California (“Caltech”).

Harris left the Air Service in 1926. He founded the world’s first aerial crop dusting business, the Huff Daland Company. Next he became a vice president and chief of operations for Grace Airways, a joint venture of Grace Shipping and Pan American World Airways, providing passenger service between South America and the West Coast of the United States.

Brigadier General Harold R. Harris, U.S. Army Air Corps.

During World War II, Harris, using his airline experience, helped to establish the Air Transport Command. In 1942, he was commissioned as a colonel in the U.S. Army Air Corps. By 1945, he was Chief, Air Transport Command, with the rank of Brigadier General.

Following World War II, Harris joined American Overseas Airlines, which soon was absorbed by Pan American. Harris was once again a vice president for Pan Am.

In 1955, Harris became president of Northwest Airlines.

Brigadier General Harold Ross Harris, United States Army Air Corps (Retired) died 28 July 1988 at the age of 92 years.

Harold Ross Harris, circa 1950. (San Diego Air and Space Museum Archives)
Harold Ross Harris, circa 1950. (San Diego Air and Space Museum Archives)

© 2016, Bryan R. Swopes