Tag Archives: N708PA

28 October 1957

The first production Boeing 707 after being rolled out of the final assembly plant at Renton, Washington, 28 October 1957. (Boeing)

28 October 1957: The first production Boeing 707 jet-powered commercial airliner, serial number 17586 (Line Number 1), was rolled out at the Boeing aircraft assembly plant at Renton, Washington. The Model 707 was developed from the earlier Model 367–80, the “Dash Eighty,” prototype for an air-refueling tanker which would become the KC-135 Stratotanker.

17586 was a Model 707-121. The new airliner had been sold to Pan American World Airways, the launch customer, as part of an order for twenty 707s in October 1955. The Federal Aviation Agency (FAA) assigned N708PA as its registration mark.

The first production Boeing 707 after roll out, 28 October 1957. (Boeing)

N708PA made its first flight 20 December 1957 with Boeing’s Chief of Flight Test, Alvin M. (“Tex”) Johnston. The airplane was initially used for flight and certification testing. Once this was completed, the new jet airliner was prepared for commercial service and delivered to Pan American at San Francisco International Airport (SFO), 30 November 1958. It was named Clipper Constitution.

Boeing 707-121 N708PA, photographed during its second flight, 20 December 1957. (Boeing)

In February 1965, the airliner was upgraded to 707-121B standards, which replaced the original turbojet engines with quieter, more efficient Pratt & Whitney Turbo Wasp JT3D-1 turbofan engines which produced 17,000 pounds of thrust. The wing inboard leading edges were modified to the design of the Model 720 and there was a longer horizontal tail plane.

Clipper Constitution flew for Pan Am for nearly 8 years, until 17 September 1965, when it crashed into Chances Peak, a 3,002 foot (915 meters) active stratovolcano on the Caribbean island of Montserrat. The point impact was 242 feet (74 meters) below the summit. All aboard, a crew of 9 and 21 passengers, were killed.

Boeing 707-121 N708PA retracts its landing gear after taking off at Seattle Tacoma Airport. (Unattributed)

The Boeing Model 707-121 was a four-engine jet transport with swept wings and tail surfaces. The leading edge of the wings were swept at a 35° angle. The airliner had a flight crew of four: pilot, co-pilot, navigator and flight engineer.

The 707-121 was 145 feet, 1 inch (44.221 meters) long with a wing span of 130 feet, 10 inches (39.878 meters). The top of the vertical fin stood 42 feet, 5 inches (12.929 meters) high. The 707 pre-dated the ”wide-body” airliners, having a fuselage width of 12 feet, 4 inches (3.759 meters).

The first versions were powered by four Pratt & Whitney Turbo Wasp JT3C-6 turbojet engines, producing 11,200 pounds of thrust (49,820 kilonewtons), and 13,500 pounds (60.051 kilonewtons) with water injection. This engine was a civil variant of the military J57 series. It was a two-spool axial-flow turbojet engine with a 16-stage compressor and 3 stage turbine. The JT3C-6 was 11 feet, 6.6 inches (3.520 meters) long, 3 feet, 2.9 inches (0.988 meters) in diameter, and weighed 4,235 pounds (1,921 kilograms).

The airliner’s empty weight is 122,533 pounds (55,580 kilograms). Maximum take off weight is 257,000 pounds (116,573 kilograms). At MTOW, the 707 required 11,000 feet (3,353 meters) of runway to take off.

The 707-121 had a maximum speed is 540 knots (1,000 kilometers per hour). Its range was 2,800 nautical miles (5,186 kilometers).

The Boeing 707 was in production from 1958 to 1979. 1,010 were built. Production of military variants continued until 1994.

© 2018, Bryan R. Swopes

3 January 1981

One of the first Boeing 707 airliners delivered to Pan American World Airways, Clipper Maria, N707PA. (Pan Am)
One of the first Boeing 707 airliners delivered to Pan American World Airways, N707PA. (Pan Am)

3 January 1981: Pan American World Airways retired its last Boeing 707 airliner. Pan Am had been the launch customer for the 707. On 20 October 1955 the airline ordered twenty 707s, and later ordered 130 more. The first one, Clipper America, a 707-121, N707PA, was delivered 15 August 1958. On 26 October 1958, N711PA, also named Clipper America,¹ made the first regularly scheduled transatlantic flight by a jet airliner.

Pan American World Airways’ Boeing 707-121, N711PA, Clipper America, arriving at Aéroport de Paris–Le Bourget, Paris, France, 27 October 1958. (Photograph © Jon Proctor, used with permission)

The Boeing Model 707-121 was a four-engine jet transport with swept wings and tail surfaces. The leading edge of the wings were swept at a 35° angle. The airliner had a flight crew of four: pilot, co-pilot, navigator and flight engineer.

The 707-121 was 145 feet, 1 inch (44.221 meters) long with a wing span of 130 feet, 10 inches (39.878 meters). The top of the vertical fin stood 41 feet, 8 inches (12.700 meters) high. The 707 pre-dated the ”wide-body” airliners, having a maximum fuselage width of 12 feet, 4.0 inches (3.759 meters). The airliner’s typical operating empty weight is 122,500 pounds (55,565 kilograms). Maximum take off weight is 257,340 pounds (116,727 kilograms).

Pan American World Airways’ Boeing 707-121 Clipper Constitution, N708PA. This was the very first production 707. (Pentakrom)

The first versions were powered by four Pratt & Whitney Turbo Wasp JT3C-6 turbojet engines, producing 11,200 pounds of thrust (49,820 kilonewtons), and 13,500 pounds (60.051 kilonewtons) with water injection. This engine was a civil variant of the military J57 series. It was a two-spool axial-flow turbojet engine with a 16-stage compressor and 2 stage turbine. The JT3C-6 was 11 feet, 6.6 inches (3.520 meters) long, 3 feet, 2.9 inches (0.988 meters) in diameter, and weighed 4,235 pounds (1,921 kilograms).

At MTOW, the 707 required 11,000 feet (3,353 meters) of runway to take off.

The 707-121 had an economical cruise speed of 550 miles per hour (885 kilometers per hour) at 35,000 feet (10,668 meters), and a maximum cruise speed of 593 miles per hour (954 kilometers per hour) at 30,000 feet (9,144 meters)—0.87 Mach. It’s range was 2,800 nautical miles (5,186 kilometers).

The Boeing 707 was in production from 1958 to 1979. 1,010 were built. Production of 707 airframes continued at Renton until the final one was completed in April 1991. As of 2011, 43 707s were still in service.

Pan American World Airway's Boeing 707-139B, N778PA, Clipper Skylark, along with many of her sisterships, in storage at Marana Air Park, Arizona.
Pan American World Airway’s Boeing 707-139B, N778PA, Clipper Skylark, along with many of her sister ships, in storage at Marana Air Park, Arizona. (Goleta Air & Space Museum)

¹ At least three Pan Am 707s carried the name Clipper America. N709PA was renamed Clipper Tradewind. N710PA, was renamed Clipper Caroline. N711PA was renamed Clipper Mayflower.

© 2019, Bryan R. Swopes

20 December 1957

Boeing 707-121 N708PA, photographed during its second flight. (Boeing via Space.com)
Boeing 707-121 N708PA, photographed during its second flight on the afternoon of 20 December 1957. (Boeing)
Boeing 707-121 N708PA makes its first takeoff at 12:30 p.m., on a rainy afternoon, 20 December 1957. (Unattributed)
Boeing 707-121 N708PA makes its first takeoff at 12:30 p.m. on a rainy afternoon, 20 December 1957. (Boeing)

20 December 1957: The first production Boeing 707 jet-powered commercial airliner, N708PA, made its first flight at Renton, Washington. Alvin M. “Tex” Johnston, Boeing’s Chief of Flight Test, was in command, with co-pilot James R. Gannet and flight engineer Tom Layne. Takeoff was at 12:30 p.m., PST. Poor weather limited the first flight to just 7 minutes. The new airliner landed at Boeing Field. Later that day, a second flight was made, this time with a duration of 1 hour, 11 minutes.

N708PA (Serial Number 17586, Line Number 1) was a Model 707-121. The new airliner had been sold to Pan American World Airways, the launch customer, as part of an order for twenty 707s in October 1955.

Boeing test pilot Alvin M. "Tex" Johnston in the cockpit of of the 367–80. (LIFE)
Boeing’s Chief of Flight Test, Alvin M. “Tex” Johnston, in the cockpit of of the 367–80, “Dash Eighty,” 1954. (LIFE Magazine via Jet Pilot Overseas)

The Boeing Model 707 was developed from the earlier Model 367–80, the “Dash Eighty,” prototype for an air-refueling tanker which would become the KC-135A Stratotanker. The 707 was a four-engine jet transport with swept wings and tail surfaces. The leading edge of the wings were swept at a 35° angle.

N708PA was initially used for flight testing by Boeing. Once this was completed, it was prepared for commercial service and delivered to Pan American at San Francisco International Airport (SFO), 30 November 1958. Pan Am named the new airliner Clipper Constitution.

Boeing 707-121 708PA under maintenance at Renton, Washington. (Boeing)
Boeing 707-121 N708PA under maintenance at Renton, Washington. (Boeing)

In February 1965, the airliner was upgraded to 707-121B standards, which replaced the original turbojet engines with quieter, more efficient Pratt & Whitney JT3D-1 turbofan engines which produced 17,000 pounds of thrust. The wing inboard leading edges were modified to the design of the Model 720 and there was a longer horizontal tail plane.

Clipper Constitution flew for Pan Am for nearly seven years, until 17 September 1965 when it crashed into Chances Peak, a 3,002 foot (915 meters) volcano on the Caribbean island of Montserrat. The point impact  was 242 feet (74 meters) below the summit. All aboard, a crew of 9 and 21 passengers, were killed.

Boeing 707-121 N708PA, with both Boeing and Pan American corporate markings. (Unattributed)
Boeing 707-121 N708PA, with both Boeing and Pan American corporate markings. (Unattributed)

The Boeing Model 707-121 was a four-engine jet transport with swept wings and tail surfaces. The leading edge of the wings were swept at a 35° angle. The airliner had a flight crew of four: pilot, co-pilot, navigator and flight engineer.

The 707-121 was 145 feet, 1 inch (44.221 meters) long with a wing span of 130 feet, 10 inches (39.878 meters). The top of the vertical fin stood 42 feet, 5 inches (12.929 meters) high. The 707 pre-dated the ”wide-body” airliners, having a fuselage width of 12 feet, 4 inches (3.759 meters). The airliner’s empty weight is 122,533 pounds (55,580 kilograms). Maximum take off weight is 257,000 pounds (116,573 kilograms).

The first versions were powered by four Pratt & Whitney Turbo Wasp JT3C-6 turbojet engines, producing 11,200 pounds of thrust (49,820 kilonewtons), and 13,500 pounds (60.051 kilonewtons) with water injection. This engine was a civil variant of the military J57 series. It was a two-spool axial-flow turbojet engine with a 16-stage compressor and 2 stage turbine. The JT3C-6 was 11 feet, 6.6 inches (3.520 meters) long, 3 feet, 2.9 inches (0.988 meters) in diameter, and weighed 4,235 pounds (1,921 kilograms).

At MTOW, the 707 required 11,000 feet (3,352.8 meters) of runway to take off.

The 707-121 had a maximum speed of 540 knots (1,000 kilometers per hour). It’s range was 2,800 nautical miles (5,186 kilometers).

The Boeing 707 was in production from 1958 to 1979. 1,010 were built. Production of 707 airframes continued at Renton until the final one was completed in April 1991. As of 2011, 43 707s were still in service.

Boeing 707-121 N708PA retracts its landing gear after taking off at Seattle Tacoma Airport. (Unattributed)
Boeing 707-121 N708PA landing at Seattle Tacoma Airport. (Unattributed)

© 2016, Bryan R. Swopes