Tag Archives: North American Aviation F-100A Super Sabre

7 April 1961

Boeing B-52B-30-BO Stratofortress 53-380. (U.S. Air Force)
Boeing B-52B-30-BO Stratofortress 53-380. (U.S. Air Force)

7 April 1961: Boeing B-52B-30-BO Stratofortress 53-380, assigned to the 95th Bombardment Wing and named Ciudad Juarez, departed Biggs Air Force Base, El Paso, Texas on a training mission. The aircraft commander was Captain Donald C. Blodgett.

The flight took Ciudad Juarez over New Mexico where they were intercepted by a flight of two North American F-100A Super Sabres of the New Mexico Air National Guard, also on a training flight.

A North American Aviation F-100A-1-NA Super Sabre, 52-5756, assigned to the New Mexico Air National Guard. (U.S. Air Force)

Captain Dale Dodd and 1st Lieutenant James W. van Scyoc had departed Kirtland Air Force Base, Albuquerque, New Mexico. Each of their Super Sabres were armed with two GAR-8 Sidewinder air-to-air missiles (later redesignated AIM-9B Sidewinder). Their assignment was to practice ground-controlled intercepts of the B-52.

Each F-100 made five passes at the B-52, flying at 34,000 feet (10,363 meters) over central New Mexico. Their Sidewinder infrared-seeking sensors would lock on to the heat of the B-52’s engines and give an audible signal to the fighter pilot that the target had been acquired. Safety precautions required that a circuit breaker be pulled and a firing switch be left in the off position. Before each pass, ground controllers had the pilots verify that the missiles were safed.

Flight of four North American F-100A Super Sabres of the 188th FIS, NMANG. (New Mexico Air National Guard)
Flight of four North American F-100A Super Sabres of the 188th FIS, NMANG. (New Mexico Air National Guard)

As the training session came to an end, Lieutenant van Scyoc, flying F-100A-20-NA Super Sabre 53-1662, announced, “OK, Wing, one more run then we’ll go home.” The seeker heads of his Sidewinders locked on to the B-52, but then one of the missiles fired.

Van Scyoc radioed, “Look out! One of my missiles is loose!” Captain Blodgett heard the warning, but before he could begin evasive maneuvering, the Sidewinder impacted the inboard engine nacelle under the bomber’s left wing, blowing the wing completely off. The B-52 immediately rolled over and went into a spin. 52-380 disappeared into the clouds 10,000 feet (3,048 meters) below.

The co-pilot of Ciudad Juarez, Captain Ray C. Obel, immediately ejected. His ejection seat was thrown through a hatch opening in the cockpit ceiling. Because of the high altitude, this sudden opening in the fuselage resulted in explosive decompression. The crew chief, Staff Sergeant Manuel A. Mieras, had been standing on a crew ladder behind the pilots which led to the lower deck where the navigator and bombardier were located. Sergeant Mieras was sucked up through the hatch. His left leg was so badly injured that it later had to amputated.

When 53-380 was assigned to the 95th Bombardment Wing, it was named Ciudad Juarez. (Unattributed)
When 53-380 was assigned to the 95th Bombardment Wing, it was named Ciudad Juarez. (Unattributed)

Captain Blodgett was pinned against the cockpit side by the g forces of the rapidly spinning bomber. He later reported:

I heard van Scyoc call “Look out! My missile’s fired.” We were on autopilot and I grabbed the controls just as the missile hit. There was a tremendous shudder and the aircraft banked left steeply. Electrical equipment in the right side of the cockpit caught fire. My copilot ejected with the aircraft in a 90° bank and in all the confusion I didn’t realize he had gone. I tried to reach the alarm bell control between the two seats to order the crew to bail out, while holding the controls with my left hand to maintain full right aileron and rudder. I didn’t realize the wing had gone and the aircraft wasn’t responding at all; it began to spin down into the clouds and I still wasn’t sure that I had hit the alarm. Later, my crew chief said he had seen the red light flashing as he sat on the steps to the lower cabin. With g-forces building up tremendously, pinning me to my seat I could not raise my right hand from its position near the bail-out alarm but could move it sideways to the ejection handle. The hatch fired and the seat threw me up fifty feet with the B-52 at 600 knots. The slipstream tore off my helmet as I left the aircraft. There was another explosion and I went through a ball of fire — it felt like being in an oven. Immediately after that I went through a “bath” of JP-4 fuel as the fuel tanks had broken up in this second explosion. At least this put out the fire but now I was soaking wet with fuel and still on the ejection seat. Assuming a seat malfunction (they told me afterwards I was holding on to it) I reached out to unfasten the lap belt when suddenly I flew out of the seat. However, the inter-phone cord wrapped around my leg so now I was going down through the clouds with a 650 pound seat hooked to my leg. I thought it would rip my leg off and I managed to claw the cord free. By now I was falling in a cloud of debris — and a blizzard. I released my survival gear pack, which also automatically released the survival raft. This was suspended about 40 feet below me and, with all the updrafts in the clouds due to the bad weather it acted like a sail, pulling me round in a 180° arc. I thought, ‘If I hit the ground sideways, this is it!’ I couldn’t get to my knife to cut it free but I soon got out of the turbulence and began to fall straight. 

When I ejected, my left arm hit the hatch putting a big gash in it. The blood was pouring out of this and I was holding this with my right hand, trying to stop the bleeding. Suddenly I saw something white and I hit the ground in a downswing of the parachute and a 30 knot wind. It felt like jumping off a two-story building. I hit so hard that everything in my survival kit: the radio, mirrors, etc., was broken apart from the survival rifle. My original intentions were to get the radio going and tell that fighter pilot what I thought of him. . . .

Aviation Safety Network, https://aviation-safety.net/wikibase/wiki.php?id=48341

Ciudad Juarez impacted on Mount Taylor, an 11,305 foot (3,446 meter) stratovolcano northeast of Grants, New Mexico, and left a crater 75 feet (23 meters) deep. Captain Peter J. Gineris, navigator, Captain Stephen C. Carter, bombardier, and 1st Lieutenant Glenn V. Blair, electronic countermeasures, did not escape.

Captain Blodgett suffered a fractured pelvis, Captain Obel, a broken back. The tail gunner, Staff Sergeant Ray A. Singleton, was badly burned.

Sergeant Singleton located Captain Blodgett and they were both rescued by helicopter later that day. It would be two days before Captain Obel and Sergeant Mieras were located.

An investigation determined that moisture condensation inside a worn electrical plug had caused a short circuit which fired the Sidewinder. Lieutenant van Scyoc was completely exonerated of any blame for the accident.

AIM-9B Sidewinder infrared-seeking air-to-air missile. (Petey21)
AIM-9B Sidewinder infrared-seeking air-to-air missile. (Petey21)

The AIM-9B Sidewinder was the first production version of the Raytheon Sidewinder 1A. It was 9 feet, 3.5 inches (2.832 meters) long with a diameter of 5 inches (12.7 centimeters). The span of the fins was 1 foot, 10 inches (55.9 centimeters). The AIM-9B weighed 155 pounds (70.3 kilograms). The missile was powered by a Thiokol Mk. 17 rocket engine which produced 4,000 pounds of thrust for 2.2 seconds. It could achieve a speed of Mach 1.7 over its launch speed, or about Mach 2.5. The maximum range was 2.9 miles (4.82 kilometers). It carried a 10 pound (4.54 kilogram) blast fragmentation warhead with an infrared detonator. The lethal range was approximately 30 feet (9.1 meters).

The Sidewinder is named after a species of rattlesnake, Crotalus cerastes, a pit viper common in the southwest United States and northern Mexico. The snake uses a heat-sensing organ on top of its head to hunt.

Mount Taylor, near Grants, New Mexico. 11,305 feet (3,664 meters).
Mount Taylor, near Grants, New Mexico. 11,305 feet (3,664 meters).

© 2016, Bryan R. Swopes

26 February 1955

North American Aviation production test pilot George Franklin Smith with a North American F-100A Super Sabre (NASM)

26 February 1955: Although it was his day off, North American Aviation production test pilot George Franklin Smith stopped by the office at Los Angeles Airport (today, known as Los Angeles International airport, or simply “LAX”, its international airport identifier). The company’s flight  dispatcher told him that a brand-new F-100A-20-NA Super Sabre, serial number 53-1659, was sitting on the flight line and needed to be test flown before being turned over to the Air Force.

North American Aviation production test pilot George F. Smith (left) walks away from an F-100 Super Sabre. (Photograph courtesy of Neil Corbett, Test and Research Pilots, Flight Test Engineeers)
North American Aviation production test pilot George F. Smith (left) walks away from an F-100 Super Sabre. (Photograph courtesy of Neil Corbett, Test and Research Pilots, Flight Test Engineeers)

Smith was happy to take the flight. He departed LAX in full afterburner and headed off shore, climbing to 35,000 feet (10,668 meters) over the Pacific Ocean to start the test sequence.

A North American F-100A-1-NA Super Sabre, 52-5757 (the second production airplane) takes off at Los Angeles International Airport. (This airplane, flown by NAA test pilot Bob Hoover, crashed east of Palmdale, California, 7 July 1955, when he could not recover from a flat spin. Hoover safely ejected but the Super Sabre was destroyed.) (North American Aviation, Inc.)

But it was quickly apparent that something was wrong: The flight controls were heavy, and then there was a hydraulic system failure that caused the Super Sabre pitch down into a dive. Smith couldn’t pull it out of the dive and the airplane’s speed rapidly increased, eventually passing Mach 1.

Smith was unable to regain control of the F-100. He had no choice but to bail out. As he ejected, Smith read the instruments: the Mach meter indicated Mach 1.05—785 miles per hour (1,263 kilometers per hour)—and the altitude was only 6,500 feet (1,981 meters).

George F. Smith recovering in hospital after his supersonic ejection. (Getty Images)
Smith recovering in hospital after his supersonic ejection. (Getty Images)

The force of the wind blast hitting him as he came out of the cockpit knocked him unconscious. Estimates are that he was subjected to a 40 G deceleration. His parachute opened automatically and he came down approximately one-half mile off Laguna Beach. Fortunately he hit the water very close to a fishing boat crewed by a former U.S. Navy rescue expert.

The F-100 dived into the Pacific Ocean approximately ¼-mile (0.4 kilometers) offshore between Dana Point and Laguna Beach.

George Smith was unconscious for six days, and when he awoke he was blind in both eyes. After four surgeries and seven months in the hospital, he recovered from his supersonic ejection and returned to flight status.

North American Aviation, Inc. F-100A-20-NA Supre Sabre 53-1646. This fighter is from the same production block as the Super Sabre flown by George F. Smith, 53-1659, 26 February 1955. (Unattributed)

George F. Smith appears in this brief U.S. Air Force informational film:

The North American Aviation F-100 Super Sabre was designed as a supersonic day fighter. Initially intended as an improved F-86D and F-86E, it soon developed into an almost completely new airplane. The fuselage incorporated the “area rule,” a narrowing in the fuselage width at the wings to increase transonic performance, similar to the Convair F-102A.

The Super Sabre had a 49° 2′ sweep to the leading edges of the wings and horizontal stabilizer. The ailerons were placed inboard on the wings and there were no flaps, resulting in a high stall speed in landing configuration. The horizontal stabilizer was moved to the bottom of the fuselage to keep it out of the turbulence created by the wings at high angles of attack. The F-100A had longer wings and a distinctively shorter vertical fin than the YF-100A. The upper segment of the vertical fin was swept 49° 43′.

North American Aviation YF-100A Super Sabre 52-5754 lands on the dry lake at Edwards Air Force Base, California. (North American Aviation, Inc.)

There were two service test prototypes, designated YF-100A, followed by the production F-100A series. The first ten production aircraft (all of the Block 1 variants) were used in the flight testing program.

The F-100A Super Sabre was 47 feet, 1¼ inches (14.357 meters) long with a wingspan of 36 feet, 6 inches (11.125 meters). With the shorter vertical fin than the YF-100A, the initial F-100As had an overall height of 13 feet, 4 inches (4.064 meters), 11 inches (27.9 centimeters) less than the YF-100A.

The F-100A had an empty weight of 18,135 pounds (8,226 kilograms), and gross weight of 28,899 pounds (13,108 kilograms). Maximum takeoff weight was 35,600 pounds (16,148 kilograms). It had an internal fuel capacity of 755 gallons (2,858 liters) and could carry two 275 gallon (1,041 liter) external fuel tanks.

Following North American Aviation test pilot George Welch’s fatal accident, 12 October 1954, NACA designed a new vertical fin for the F-100A. It was taller but also had a longer chord. This resulted in a 10% increase in area. (NASA E-1573)

The early F-100As were powered by a Pratt & Whitney Turbo Wasp J57-P-7 afterburning turbojet engine. It was rated at 9,700 pounds of thrust (43.148 kilonewtons) for takeoff, and 14,800 pounds (65.834 kilonewtons) with afterburner. Later production aircraft used a J57-P-39 engine. The J57 was a two-spool axial flow turbojet which had a 16-stage compressor, and a 3-stage turbine. (Both had high- and low-pressure stages.) The engine was 15 feet, 3.5 inches (4.661 meters) long, 3 feet, 5.0 inches (1.041 meters) in diameter, and weighed 4,390 pounds (1,991 kilograms).

Test Pilot A. Scott Crossfield flew this F-100A-5-NA, 52-5778, in flight testing at the NACA High Speed Flight Station, October–December 1954. (NASA)

The Super Sabre was the first U.S. Air Force fighter capable of supersonic speed in level flight. It could reach 760 miles per hour (1,223 kilometers) at Sea Level. (Mach 1 is 761.1 miles per hour, 1,224.9 kilometers per hour, under standard atmospheric conditions.) Its maximum speed was 852 miles per hour (1,371 kilometers per hour) at 35,000 feet (10,668 meters). The service ceiling was 44,900 feet (13,686 meters). Maximum range with external fuel was 1,489 miles (2,396 kilometers).

The F-100 was armed with four M-39 20 mm autocannons, capable of firing at a rate of 1,500 rounds per minute. The ammunition capacity of the F-100 was 200 rounds per gun.

North American Aviation built 199 F-100A Super Sabres at its Inglewood, California, plant before production shifted to the F-100C fighter bomber variant. Approximately 25% of all F-100As were lost in accidents.

This is the fifth production F-100A-1-NA Super Sabre, 52-5760, in flight southeast of San Bernardino, California. In this photograph, FW-760 has the taller vertical fin that was designed to improve the Super Sabre’s controllability. (U.S. Air Force)

© 2019, Bryan R. Swopes

12 October 1954

North American Aviation’s Chief Engineering Test Pilot, George S. Welch, with the first prototype YF-100A Super Sabre, 52-5754. (U.S. Air Force)

12 October 1954: North American Aviation Chief Engineering Test Pilot George S. Welch, testing the ninth production F-100A-1-NA Super Sabre, serial number 52-5764, made a planned 7.3 G pullout from a Mach 1.55 dive to verify the aircraft’s design limits.

A Boeing B-47 Stratojet crew flying at 25,000 feet (7,620 meters) reported that Welch’s F-100 winged over and began a rapid descent, passing within four miles (6.4 kilometers) of their position and diving at a very high speed. The aircraft appeared to be under control but then suddenly disintegrated.

The Super Sabre had encountered Inertial Roll Coupling. It went out of control and then disintegrated. Its nose folded over the windshield, crushing Welch in his seat. The vertical fin broke away. The ejection seat fired but because of the supersonic speeds the parachute was shredded.

Welch was still alive when rescue teams arrived. He died while being flown to a hospital by helicopter.

George S. Welch, North American Aviation test pilot, wearing his orange flight helmet. An F-86 Sabre is in the background. (San Diego Air and Space Museum Photo Archives)

Inertial roll coupling led to the death of test pilot Mel Apt when his rocket-powered airplane, the Bell X-2, went out of control at Mach 3.2 It nearly killed Chuck Yeager when he lost control of the Bell X-1B at Mach 2.4. It is a complex phenomenon which I will briefly attempt to explain:

To increase maximum speed of transonic and supersonic airplanes during the late 1940s and early 1950s, their wings and tail surfaces were made smaller in order to decrease aerodynamic drag. At the same time, the fuselage became longer and the placement of engines, armament, landing gear, fuel, etc., within the fuselage concentrated the airplane’s mass near its center. While the gyroscopic effects of the turbojet engine contributed some degree of longitudinal stability, the torque effect made rolls to the left occur more easily, but with a higher rate than a roll to the right. The resistance to a change in attitude—inertia—decreased at the same time that the control surfaces’ ability to control the airplanes’ attitude also decreased. The airplanes became unstable.

This North American Aviation F-100-1-NA Super Sabre, 52-5761, is from the same production black as the aircraft flown by George Welch, 12 October 1954. (U.S. Air Force)
This North American Aviation F-100-1-NA Super Sabre, 52-5761, is from the same production block as the aircraft flown by George Welch, 12 October 1954. This photograph shows FW-761 with the original short vertical fin of the F-100A. (North American Aviation, Inc.)
North American Aviation F-100A-1-NA Super Sabre  52-5763, sister ship of the airplane flown by George Welch, 12 October 1954. (North American Aviation, Inc.)

When George Welch tried to pull the F-100 out of its supersonic dive, the airplane’s speed began to decrease as the angle of attack increased. The wings’ ability to stabilize the natural roll instability of the fuselage’s concentrated mass was lessened, and the ailerons could not provide sufficient control to counteract this rolling tendency. The low vertical fin of the original F-100A did not provide adequate directional stability. The Super Sabre rolled and then yawed, entering a side slip. This caused the Super Sabre to pitch down and it was suddenly out of control in all three axes. The physical forces exceeded the strength of the aircraft structure and it came apart.¹

[Aerodynamicists and Aeronautical Engineers: Your corrective comments are welcome.]

Wreckage of North American Aviation F-100A Super Sabre, 12 October 1954. (U.S. Air Force)
Wreckage of North American Aviation F-100A-1-NA Super Sabre 52-5764, 12 October 1954. (North American Aviation, Inc.)

Following the death of George Welch, NACA High Speed Flight Station research test pilot Albert Scott Crossfield spent three months conducting flight tests of the F-100A, demonstrating its inertial roll coupling characteristics using three different vertical fins. F-100A-5-NA 52-5778 was Crossfield’s test aircraft.

Scott Crossfield flew the F-100A-5-NA, 52-5778, in flight testing at the NACA High Speed Flight Station, October–December 1954. (NASA)
Test Pilot A. Scott Crossfield flew this F-100A-5-NA, 52-5778, in flight testing at the NACA High Speed Flight Station, October–December 1954. (NASA)

The North American Aviation F-100 Super Sabre was designed as a supersonic day fighter. Initially intended as an improved F-86D and F-86E, the “Sabre 45” soon developed into an almost completely new airplane. The Super Sabre had a 49° 2′ sweep to the leading edges of the wings and horizontal stabilizer. The total wing area was 385.2 square feet (35.79 square meters). The wings had an angle of incidence of 0°, with no twist or dihedral. The ailerons were placed inboard on the wings and there were no flaps, resulting in a high stall speed in landing configuration. The horizontal stabilizer was moved to the bottom of the fuselage to keep it out of the turbulence created by the wings at high angles of attack. The F-100A had a distinctively shorter vertical fin than the YF-100A. The upper segment of the vertical fin was swept 49° 43′.

There were two service test prototypes, designated YF-100A, followed by the production F-100A series. The first ten production aircraft (all of the Block 1 variants) were used in the flight testing program.

The F-100A Super Sabre was 47 feet, 1¼ inches (14.357 meters) long with a wingspan of 36 feet, 6 inches (11.125 meters). With the shorter vertical fin, the initial F-100As had an overall height of 13 feet, 4 inches (4.064 meters), 11 inches (27.9 centimeters) less than the YF-100A.

Following Welch's accident, NACA designed a new vertical fin for the F-100A. Ii was taller but also had a longer chord. This resulted in a 10% increase in area. (NASA E-1573)
Following Welch’s accident, the NACA High Speed Flight Station tested the Super Sabre and designed a new vertical fin for the F-100A. The two F-100As in this photograph are both from the second production block (F-100A-5-NA). 52-5778, on the left, has the new fin, while 52-5773 retains the original short fin. The new fin is taller but also has a longer chord. This resulted in a 10% increase in area. (NASA)

The F-100A had an empty weight of 18,135 pounds (8,226 kilograms), and its maximum takeoff weight was 28,971 pounds (13,141 kilograms). It had an internal fuel capacity of 744 gallons (2,816 liters) and could carry two 275 gallon (1,041 liter) external fuel tanks.

The early F-100As were powered by a Pratt & Whitney Turbo Wasp J57-P-7 afterburning turbojet engine. The J57 was a two-spool axial-flow turbojet which had a 16-stage compressor section (9 low- and 7 high-pressure stages) and a 3-stage turbine (2 high- and 1 low-pressure stages). Its continuous power rating was 8,000 pounds of thrust (35.586 kilonewtons). The Military Power rating was 9,700 pounds (43.148 kilonewtons) (30-minute limit). Maximum power was 14,800 pounds (43.148 kilonewtons) with afterburner (5-minute limit). The engine was 20 feet, 9.7 inches (6.342 meters) long, 3 feet, 3.9 inches (1.014 meters) in diameter, and weighed 5,075 pounds (2,303 kilograms). Later production aircraft used a J57-P-39 engine.

The Super Sabre was the first U.S. Air Force fighter capable of supersonic speed in level flight. It could reach 760 miles per hour (1,223 kilometers) at Sea Level. (Mach 1 is 761.1 miles per hour at Sea Level, 1,224.9 kilometers per hour, under Standard Atmospheric Conditions.) The maximum speed of the F-100A was 759 knots (873 miles per hour/1,406 kilometers per hour)—Mach 1.32—at 35,000 feet (10,668 meters). Its service ceiling was 47,500 feet (14,478 meters). The fighter’s combat radius was 402 nautical miles (463 statute miles/745 kilometers). The maximum ferry range with external fuel was 1,124 nautical miles (1,493 statute miles/2,082 kilometers).

The F-100 was armed with four M-39 20 mm autocannons, capable of firing at a rate of 1,500 rounds per minute. The ammunition capacity of the F-100 was 200 rounds per gun.

North American Aviation built 199 F-100A Super Sabres at its Inglewood, California, plant before production shifted to the F-100C fighter bomber variant. Approximately 25% of all F-100As were lost in accidents.

his is the fifth production F-100A-1-NA Super Sabre, 52-5760, in flight southeast of San Bernardino, California. This fighter is from the same production block as 52-5764, the fighter being tested by George Welch, 12 October 1954. In this photograph, FW-760 has the taller vertical fin that was designed to improve the Super Sabre's controlability. (U.S. Air Force)
This is the fifth production F-100A-1-NA Super Sabre, 52-5760, in flight southeast of San Bernardino, California, 24 June 1955. This fighter is from the same production block as 52-5764, the fighter being tested by George Welch, 12 October 1954. In this photograph, FW-760 has the taller vertical fin that was designed by NACA to improve the Super Sabre’s stability. (North American Aviation, Inc.)

George Welch was born George Lewis Schwartz, Jr., in Wilmington, Delaware, 10 May 1918. He was the first of two sons of George Lewis Schwartz, a chemist at the Dupont Experimental Station in Wilmington, and Julia Welch Schwartz. His parents changed his surname to Welch, his mother’s maiden name, so that he would not be effected by the anti-German prejudice that was widespread in America following World War I.

He studied mechanical engineering at Purdue University, Indiana, and enlisted in the Army Air Corps in 1939. Welch graduated from pilot training at Kelly Field, Texas, and on 4 October 1940, was commissioned as a second lieutenant, U.S. Army Air Corps.

Second Lieutenant Kenneth M. Taylor and Second Lieutenant George S. Welch, 47th Pursuit Squadron, 15th Pursuit Group, the two Curtiss P-40B Warhawk pilots who shot down 8 Japanese aircraft during the attack on Pearl Harbor, Hawaii, 7 December 1941. Both officers were awarded the Distinguished Service Cross. (U.S. Air Force)

George S. Welch is best remembered as one of the heroes of Pearl Harbor. He, along with Second Lieutenant Kenneth M. Taylor, were the only two fighter pilots to get airborne from Haleiwa Auxiliary Airfield during the Japanese surprise attack on Hawaii, 7 December 1941. Flying a Curtiss P-40B Warhawk, he shot down three Aichi D3A “Val” dive bombers and one Mitsubishi A6M2 Zero fighter. Taylor also shot down four Japanese airplanes. For this action, Lieutenant General Henry H. “Hap” Arnold recommended the Medal of Honor, but because Lieutenants Welch and Taylor had taken off without orders, an officer in their chain of command refused to endorse the nomination. Both fighter pilots were awarded the Distinguished Service Cross.

During the War, Welch flew the Bell P-39 Airacobra and Lockheed P-38 Lightning on 348 combat missions. He had 16 confirmed aerial victories over Japanese airplanes and rose to the rank of Major. In addition to the Distinguished Service Cross, George Welch was awarded the Silver Star, the Distinguished Flying Cross with two oak leaf clusters (three awards), the Air Medal with one oak leaf cluster (two awards), the Presidential Unit Citation with two oak leaf clusters (three awards), American Defense Service medal with one service star, American Campaign Medal, Asiatic-Pacific Campaign Medal with one silver and one bronze star (six campaigns), and the World War II Victory Medal.

George Welch, circa 1943. (Unattributed)
George Welch, circa 1943. (Unattributed)

Welch received the nickname, “Wheaties,” because he was the first military officer to be featured on a box of Wheaties cereal. (Wheaties, “The Breakfast of Champions,” was a toasted wheat bran cereal produced by General Mills. It normally featured champion athletes on its distinctive orange-colored boxes.)

Suffering from malaria, George Welch was out of combat and recuperating in Australia. There he met Miss Janette Alice Williams and they were soon married. Welch returned to the United States with his new wife. They had a son, Giles, born in October 1947. Their home was in Brentwood, California.

North American Aviation approached General Arnold to recommend a fighter pilot who could bring his combat experience to testing new fighters. Welch was one of two that General Arnold suggested. The general authorized Welch’s release from active duty so that he could join North American. Welch held the rank of major, Air Reserve, from 13 November 1944 to 1 April 1953.

George S. Welch, now a civilian test pilot forNorth American Aviation, Inc., sits on the canopy rail of a P-51H Mustang, circa 1945. (North American Aviation Inc.)
George S. Welch, now a civilian test pilot for North American Aviation, Inc., sits on the canopy rail of a P-51H Mustang, circa 1945. (North American Aviation Inc.)

Welch went on to test fly the North American P-51H Mustang, FJ-1 Fury, F-86 Sabre and F-100 Super Sabre.

George Welch made the first flight of the XP-86 prototype, 1 October 1947. There is some evidence that on that flight, and during a subsequent flight on 14 October, Welch exceeded the speed of sound while in a dive. It has been said that during the Korean War, while teaching U.S. Air Force pilots how to best use the F-86 Sabre, he shot down several enemy MiG-15 jet fighters.

George S. Welch is buried at the Arlington National Cemetery, Section 6, Site 8578-D.

¹ Recommended: Coupling Dynamics in Aircraft: A Historical Perspective, by Richard E. Day, Dryden Flight Research Center, Edwards AFB, California. NASA Special Publications 532, 1997.

© 2018, Bryan R. Swopes

8 September 1954

Albert Scott Crossfield, NACA Test Pilot. (LIFE Magazine via Jet Pilot Overseas)
Albert Scott Crossfield, NACA Test Pilot. (Allan Grant/LIFE Magazine)

8 September 1954: Scott Crossfield, a NACA Aeronautical Research Pilot at the High Speed Flight Station, Edwards Air Force Base, California, took the North American Aviation F-100A-5-NA Super Sabre, 52-5778, on its first NACA test flight—and his first flight in an F-100.

Tests of the prototype and early production Super Sabres revealed directional stability problems, a very dangerous inertia coupling characteristic that could cause the aircraft to go violently out of control (and which would result in the death of North American’s chief test pilot, George Welch, in just another three weeks). The highly swept wings could stall at high angles of attack, causing the airplane to pitch up in the deadly “Sabre dance.” NACA wanted to explore the causes of these aerodynamic problems and design solutions.

Scott Crossfield pre-flights a North American Aviation F-100A Super Sabre. Note the extended leading-edge "slats". (LIFE Magazine via Jet Pilot Overseas.)
Scott Crossfield pre-flights a North American Aviation F-100A Super Sabre. Note the extended leading-edge “slats”. (Allan Grant/LIFE Magazine)

During the flight there was an engine fire warning and Crossfield shut down the Pratt & Whitney J57-P-7 turbojet engine. The F-100A had no flaps and North American’s own test pilots did not think a “dead stick” landing was possible due the very high landing speed required.

Scott Crossfield signs the maintenance forms for an F-100, certifying the airplane ready for flight. (LIFE Magazine via Jet Pilot Overseas)
Scott Crossfield signs the maintenance forms for an F-100, certifying the airplane ready for flight. (Allan Grant/LIFE Magazine)

Scott Crossfield tells the story in his autobiography:

. . . As a matter of fact, North American tests pilots were then flipping coins to see who would bring an F-100 in dead-stick to fulfill a requirement of the Air Force acceptance tests. I was not concerned. Dead-stick landings in low L-over-D [Lift-over-Drag] airplanes were my specialty. Every test pilot develops a strong point. I was certain that my talent lay in dead-stick landings.

With the engine idling and generating no energy to the plane’s systems, I was running out of hydraulic pressure to operate the controls. Following the handbook instructions, I pulled a lever which extended a miniature “windmill” into the slipstream. This “windmill” churned, building up pressure in the hydraulic lines. Unknown to me, there was a major leak in the line. The windmill was not helping, but hurting me. It was pumping hydraulic fluid overboard as fast as it could turn.

Scott Crossfield climbs into the cockpit of a North American Aviation F-100A-5-NA Super Sabre. (LIFE Magazine via Jet Pilot Overseas)
Scott Crossfield climbs into the cockpit of a North American Aviation F-100A-5-NA Super Sabre. (Allan Grant/LIFE Magazine)

I called Edwards tower and declared an emergency. All airborne planes in the vicinity of the base were warned away from the lake area. I held the ailing F-100 on course, dropping swiftly, following the glide path that I used for the dead-stick Skyrocket. [Douglas D-558-II Skyrocket] I flared out and touched down smoothly. It was one of the best landings I have ever made, in fact. Seconds later, while the F-100 was rolling out, the remaining bit of hydraulic pressure in the control lines drained out and the controls froze.

I then proceeded to violate a cardinal rule of aviation: never try tricks with a compromised airplane. The F-100 was still rolling at a fast clip, coming up fast on the NACA ramp, when I made my poor decision. I had already achieved the exceptional, now I would end it with a flourish, a spectacular wind-up. I would snake the stricken F-100 right up the ramp and bring it to a stop immediately in front of the NACA hangar. This trick, which I had performed so often in the Skyrocket, was a fine touch. After the first successful dead-stick landing in an F-100, it would be fitting.

Instrument panel of a North American Aviation F-100 Super Sabre. (U.S. Air Force)
Instrument panel of a North American Aviation F-100 Super Sabre. The fire warning light and hydraulic pressure gauge are at the upper right corner. (U.S. Air Force)

According to the F-100 handbook, the hydraulic brake system—a separate hydraulic system from the controls—was good for three “cycles,” engine out. This means three pumps on the brake, and that proved exactly right. The F-100 was moving at about fifteen miles an hour when I turned up the ramp. I hit the brakes once, twice, three times. The plane slowed, but not quite enough. I was still inching ahead ponderously, like a diesel locomotive. I hit the brakes a fourth time—and my foot went clear to the floorboards. The hydraulic fluid was exhausted. The F-100 rolled on, straight between the yawning hangar doors!

The good Lord was watching over me—partially anyhow. The NACA hangar was then crowded with expensive research tools—the Skyrocket, all the X-1 series, the X-3, X-4 and X-5. Yet somehow, my plane, refusing to halt, squeezed by them all and bored steadily on toward the side wall of the hangar.


The nose of the F-100 crunched through the corrugated aluminum, punching out an eight-inch steel I-beam. I was lucky. Had the nose bopped three feet to the left or right, the results could have been catastrophic. Hitting to the right, I would have set off the hangar fire-deluge system, flooding the hangar with 50,000 barrels of water and ruining all the expensive airplanes. Hitting to the left, I would have dislodged a 25-ton hangar-door counterweight, bringing it down on the F-100 cockpit, and doubtless ruining Crossfield.

Chuck Yeager never let me forget the incident. He drew many laughs at congregations of pilots by opening his talk: “Well, the sonic wall was mine. The hangar wall was Crossfield’s.” That’s the way it was at Edwards. Hero one minute, bum the next. That I was the first pilot to land an F-100 dead-stick successfully, and memorized elaborate and complete instrument data on the engine failure besides, was soon forgotten.

The F-100 is a tough bird. Within a month NACA’s plane was flying again, with Crossfield back at the helm. In the next few weeks I flew forty-five grueling flights in the airplane, pushing it to the limits, precisely defining the roll coupling. (On one flight the coupling was so severe that it cracked a vertebra in my neck.) These data confirmed, in actual flight, the need for a new F-100 tail, which North American was planning to install on later models of the airplane.

Every night after landing, I taxied the F-100 slowly to the NACA ramp. At the bottom, placed there on orders of Walt Williams, there was a large new sign, symbolic of the new atmosphere at Edwards. It said:

PLEASE COME TO A COMPLETE STOP BEFORE TAXIING UP RAMP 

Always Another Dawn, The Story Of A Rocket Test Pilot, by A. Scott Crossfield with Clay Blair, Jr., The World Publishing Company, Cleveland and New York, 1960. Chapter 20 at Pages 196–199.

North American F-100A-5-NA Super Sabre parked on Rogers Dry Lake, 1959. It had been repaired and returned to service after running through the NACA hangar wall at Edwards AFB, 8 September 1954. In 1960, FW-778 was retired to Davis-Monthan AFB, Tucson, AZ. (NASA)
North American Aviation F-100A-5-NA Super Sabre 52-5778 parked on Rogers Dry Lake, 1959. It had been repaired and returned to service after running through the NACA hangar wall at Edwards AFB, 8 September 1954. In 1960, FW-778 was retired to Davis-Monthan AFB, Tucson, AZ. (NASA)
North American Aviation F-100A-5-NA Super Sabre 52-5778. (NASA)
North American Aviation F-100A-5-NA Super Sabre 52-5778. (NASA)
North American Aviation F-100A-5-NA Super Sabre 52-5778. (NASA)
North American Aviation F-100A-5-NA Super Sabre 52-5778. (NASA)
North American Aviation F-100A-5-NA Super Sabre 52-5778 parked on the ramp in front of the NACA hangar, Edwards Air Force Base, California, 1959. (NASA)
North American F-100A Super Sabre on the ramp near the NACA High-Speed Flight Station in 1957. (NASA)
NACA High Speed Flight Station, 24 August 1954. The Boeing P2B-1S Superfortress is parked at the northeast corner of the ramp. (NASA DFRC E54-1361)

© 2017, Bryan R. Swopes